Omada L3 Campus Stackable Managed Switch User Manual

Hevitra ato Anatiny afeno ny

1 L3 Campus Stackable Managed Switch

2 fepetra arahana

3 Torolàlana momba ny fampiasana vokatra

3.1 Toko 2: Fametrahana

3.2 Toko 3: Fifandraisana

3.3 Toko 4: Fanamboarana

4 FAQ

4.1 Q: What should I do if the LED indications show an error?

4.2 Documents / Loharano

4.2.1 References

L3 Campus Stackable Managed Switch

“

fepetra arahana

Model: Omada Campus Stackable L3 Managed Switch
Front Panel: Mode Selection Button, Management Port, LED,
Console Port USB2.0 Port (Type-C/RJ45), 1G RJ45 Port, 10G SFP+ Slot
LED
LED famantarana:
- PWR1*: Green On (switch powered by PWR1), Off (PWR2
  disconnected or not working properly)
- PWR2: Green On (switch powered by PWR1 and PWR2 connected),
  Yellow On** (PWR2 powered), Off (PWR1 disconnected or not working
  araka ny tokony ho izy)
- LED SYS FAN: Green On (all fans work properly), Yellow On (not
  all fans work properly)
- MGMT: On (device linked to port), Flashing (transmitting or
  receiving data), Off (no device linked to port)
- MST: On (device linked to port), Flashing (transmitting or
  receiving data), Off (no device linked to port)

Torolàlana momba ny fampiasana vokatra

Toko 2: Fametrahana

Alohan'ny hanombohan'ny dingan'ny fametrahana dia ataovy azo antoka fa manana ny zava-drehetra ianao
the necessary tools and follow safety precautions.

Fonosana: Check all items mentioned in
ny fonosana.
Fiarovana fiarovana: Araho ny torolalana amin'ny
miantoka ny fametrahana azo antoka.
Fitaovana fametrahana: Gather all tools required
ho an'ny fametrahana.
Fametrahana vokatra: Araho ny dingana tsirairay
instructions provided in the manual for successful
fametrahana.

Toko 3: Fifandraisana

After installation, connect the switch to the network using
appropriate cables and ports as per your network setup.

Toko 4: Fanamboarana

Configure the switch based on your requirements. You can choose
between Standalone Mode or Controller Mode as per your network
mila.

FAQ

Q: What should I do if the LED indications show an error?

A: If the LED indications suggest improper functioning, check
the power sources and connections. Refer to the troubleshooting
fizarana ao amin'ny boky torolalana ho fanampiana fanampiny.

“`

View Fullscreen

Vahaolana Networking Solution
Torolàlana fametrahana
Omada Campus Stackable L3 Managed Switch

Momba ity torolàlana fametrahana ity
Ity torolàlana momba ny fametrahana ity dia mamaritra ny toetran'ny fitaovana, ny fomba fametrahana ary ny teboka tokony hodinihina mandritra ny fametrahana. Ity torolàlana momba ny fametrahana ity dia voarafitra toy izao manaraka izao: Fizarana 1 Fampidirana Ity toko ity dia mamaritra ny singa ivelany amin'ny switch. Toko 2 Fametrahana Ity toko ity dia mampiseho ny fomba fametrahana ny switch. Toko 3 Fifandraisana Ity toko ity dia mampiseho ny fomba hanaovana ny fifandraisana ara-batana amin'ny switch. Toko 4 Configuration Ity toko ity dia mampiseho ny fomba fanamboarana ny switch. Tovana A Famahana olana Tovana B

Mpijery

Ity torolàlana fametrahana ity dia ho an'ny:

Network Engineer

Mpitantana tambajotra

fivoriambe
· Ny modely sasany asongadina ato amin'ity torolalana ity dia mety tsy hita ao amin'ny firenenao na ny faritra misy anao. Raha mila fampahalalana momba ny varotra eo an-toerana, tsidiho ny https://www.omadanetworks.com/.
· Ny tarehimarika ao amin'ny Toko 2, Toko 3, ary Toko 4 dia natao ho an'ny fampisehoana fotsiny. Mety tsy mitovy amin'ny sary aseho ny switch-nao.
· Ny kajy tetibola PoE dia mifototra amin'ny fitiliana laboratoara. Ny tena teti-bolan'ny herin'ny PoE dia tsy azo antoka ary hiovaova arakaraka ny fetran'ny mpanjifa sy ny anton'ny tontolo iainana.
· Ity torolàlana ity dia mampiasa ireo endrika manokana hanasongadinana ireo hafatra manokana. Ity tabilao manaraka ity dia mitanisa ireo kisary fampandrenesana izay ampiasaina mandritra ity torolàlana ity.

Ampahatsiahivo hitandrina. Ny fitandremana dia manondro mety hitranga izay mety hiteraka fahasimban'ny fitaovana.
Ampahatsiahivo handray izany. Ny naoty dia misy fampahalalana mahasoa amin'ny fampiasana tsara kokoa ny vokatra.

Rakitra mifandraika
Ny Torolàlana ho an'ny mpampiasa sy ny torolàlana momba ny CLI momba ny vokatra dia omena ao amin'ny Download Center. Raha te hahazo ny mombamomba ny vokatra farany dia tsidiho ilay tompon'andraikitra webtranokala: https://support.omadanetworks.com/document/.

Hevitra ato Anatiny
Toko 1 Fampidirana ———————- 01
1.1 Ny vokatraview ………………………………………………………..01 1.2 Fisehoana………………………………………………………………..01
Toko 2 Fametrahana ———————- 12
2.1 Ny votoatin'ny fonosana ……………………………………………………….12 2.2 Fiarovana amin'ny fiarovana ………………………………………………………12 2.3 Fitaovana Fametrahana………………………………………………..14 2.4 Fametrahana vokatra ……………………………………………..14
Toko 3 Fifandraisana ———————- 22
3.1 Ethernet Port …………………………………………………………..22 3.2 10G SFP+/25G SFP28/100G QSFP28 Slot ………..22 3.3 Console Port ……………………………………………………………22 3.4 Verify Installation…………………………………………………….23 3.5 Power On ………………………………………………………………….24 3.6 Initialization………………………………………………………………24 3.7 Stack Topology ……………………………………………………….24
Toko 4 Fanovana ——————– 27
4.1 Famaranana ny Configurationview…………………………………27 4.2 Fomba Mitokana……………………………………………………27 4.3 Fomba fanaraha-maso………………………………………………………28
Tovana A Famahana olana —————- 32
Fanazavana fanampiny B —————— 33

Omada Campus Stackable L3 Managed Switch

Toko 1 Fampidirana

1.1 Ny vokatraview
Natao ho an'ny orinasa sy campus, Omada Campus Stackable L3 Managed Switch provides wire-speed performance and abundant L2 and L3 management features. It provides a variety of service features and multiple powerful functions with high security. The EIA-standardized framework and smart configuration capacity can provide flexible solutions for a variable scale of networks. Static Routing, RIP, OSPF, BGP, IS-IS, PIM-SM/DM/SSM, and ECMP come with abundant Layer 3 routing protocols that support a scalable network. Physically stacking for builtin redundancy and performance. Redundant power supplies and fans make it an ideal choice for reliable networking architecture. VRRP allows a group of switches to dynamically back up each other. ERPS supports rapid protection and recovery in a ring topology. MACsec, secure boot, ACL, 802.1x and Dynamic ARP Inspection provide robust security strategies. QoS and IGMP snooping/filtering optimize voice and video application. Link aggregation (LACP) increases aggregated bandwidth, optimizing the transport of business critical data. SNMP, RMON, WEB, Netconf and CLI Log-in bring abundant management policies. These switches integrate multiple functions with excellent performance, and is friendly to manage, which can fully meet the need of the users demanding higher networking performance. S6500-24GP4XF/S6500-48GP6XF/S6500-24MPP4Y/S6500-48MPP6Y is also a Power Sourcing Equipment (PSE*). The RJ45 ports that support Power over Ethernet (PoE*) function can automatically detect and supply power to those powered devices (PDs*) complying with IEEE 802.3af, IEEE 802.3at, and IEEE 802.3bt (only for S6500-24MPP4Y/S6500-48MPP6Y). *PSE: a device (switch or hub for instance) that provides power through an Ethernet cable. *PoE: This technology describes a system to transmit electrical power, along with data, to remote devices over standard twisted-pair cable in an Ethernet. *PD: a device powered by a PSE and thus consumes energy. ExampAnisan'izany ny fakan-tsarimihetsika matanjaka, teboka fidirana LAN tsy misy tariby, telefaona IP, habaka tambajotra, solosaina napetraka sns.
1.2 Fisehoana
Front Panel (The figure is for demonstration only. It may differ from your actual product. )
The front panel of S6500-24G4XF is shown as the following figure.
Button Selection Mode
Seranan-tsambo fitantanana

LED

Console Port USB2.0 Port (Type-C/RJ45)

1G RJ45 Port

10G SFP+ Slot LED

The front panel of S6500-48G6XF is shown as the following figure.
Button Selection Mode
Seranan-tsambo fitantanana

LED

Console Port USB2.0 Port (Type-C/RJ45)

1G RJ45 Port

10G SFP+ Slot LED

Fampidirana 01

Omada Campus Stackable L3 Managed Switch

LED famantarana

PWR1*

PWR2

Maitso On

NIALA

Maitso On

Yellow On**

NIALA

Maitso On

NIALA

famantarana
Ny switch dia ampiasain'ny PWR1. Tapaka ny PWR2 na tsy mandeha araka ny tokony ho izy.
Ny switch dia ampiasain'ny PWR1. Mifandray ny PWR1 sy ny PWR2.*
Ny switch dia ampiasain'ny PWR2. Tapaka ny PWR1 na tsy mandeha araka ny tokony ho izy.
Tsy mandeha ny switch na samy miasa tsy araka ny tokony ho izy ny PWR1 sy PWR2.

LED SYS FAN
MGMT
MST
Port 1-24 of S6500-24G4XF/ Port 1-48 of S6500-48G6XF
(When the SPEED LED is on)
Port 1-24 of S6500-24G4XF/ Port 1-48 of S6500-48G6XF
(Rehefa mandeha ny LED STK)
Port 25-28 of S6500-24G4XF/ Port 49-54 of S6500-48G6XF ***

famantarana
Mitselatra: Miasa tsara ny switch. On na Off: Tsy mandeha araka ny tokony ho izy ny switch.
Green On: Miasa tsara ny mpankafy rehetra. Yellow On: Tsy ny mpankafy rehetra no miasa tsara.
On: A device is linked to the port. Flashing: Transmitting or receiving data. Off: No device is linked to the port.
On: The device functions as the master switch in the stack topology or it works individually. Off: The device functions as the member switch in the stack topology.
Green On: Mandeha amin'ny 1000 Mbps, fa tsy misy hetsika. Green Flash: mihazakazaka amin'ny 1000 Mbps ary mandefa na mandray angona. Yellow On: Mandeha amin'ny 10Mbps/100 Mbps, fa tsy misy hetsika. Mitselatra mavo: Mihazakazaka amin'ny 10Mbps/100 Mbps ary mandefa na mandray angona. Off: Tsy misy fitaovana mifandray amin'ny seranan-tsambo mifanaraka aminy.
On: Ny laharan'ny seranan-tsambo dia manondro ny ID unit ao amin'ny topologie stack.
Maitso On: Mihazakazaka amin'ny 10 Gbps, fa tsy misy hetsika. Green Flash: mihazakazaka amin'ny 10 Gbps ary mandefa na mandray angona. Mavo Mandeha: Mandeha amin'ny 1 Gbps, fa tsy misy hetsika. Mitselatra mavo: Mihazakazaka amin'ny 1 Gbps ary mandefa na mandray angona. Off: Tsy misy fitaovana mifandray amin'ny seranan-tsambo mifanaraka aminy.

*PWR1 is the primary power supply and it takes priority over PWR2. When the device is powered by PWR1, PWR2 will be working in the backup mode.
** Rehefa samy miasa tsara ny PWR1 sy ny PWR2 ary ny PWR1 no miasa, dia mila 10-20 segondra vao mivoaka ny LED PWR2 (mavo) rehefa nesorina ny PWR2.
***All 10 Gbps SFP+ slots can be used as uplink ports or stacking ports. When used as stacking ports, the slots need to run at the highest speed.

02 Fampidirana

Omada Campus Stackable L3 Managed Switch The front panel of S6500-24GP4XF is shown as the following figure.

Button Selection Mode
Seranan-tsambo fitantanana
LED Console Port USB2.0 Port (Type-C/RJ45)

1G RJ45 Port

10G SFP+ Slot LED

Ny tontonana anoloana S6500-48GP6XF dia aseho amin'ny sary manaraka.

Button Selection Mode
Seranan-tsambo fitantanana
LED Console Port USB2.0 Port (Type-C/RJ45)

1G RJ45 Port

10G SFP+ Slot LED

The front panel of S6500-24M4Y is shown as the following figure.

Button Selection Mode
Seranan-tsambo fitantanana
LED Console Port USB2.0 Port (Type-C/RJ45)

2.5G RJ45 Port

25G SFP28 Slot LED

The front panel of S6500-24MPP4Y is shown as the following figure.

Button Selection Mode
Seranan-tsambo fitantanana
LED Console Port USB2.0 Port (Type-C/RJ45)

2.5G RJ45 Port

25G SFP28 Slot LED

Fampidirana 03

Omada Campus Stackable L3 Managed Switch The front panel of S6500-48M6Y is shown as the following figure.

Button Selection Mode
Seranan-tsambo fitantanana

LED Console Port USB2.0 Port (Type-C/RJ45)

2.5G RJ45 Port

The front panel of S6500-48MPP6Y is shown as the following figure.

25G SFP28 Slot LED

Button Selection Mode
Seranan-tsambo fitantanana
LED Console Port USB2.0 Port (Type-C/RJ45)

2.5G RJ45 Port

25G SFP28 Slot LED

LED Indication LED
PWR1* PWR2
SYS FAN PoE MAX
(For S6500-24GP4XF, S6500-48GP6XF, S6500-24MPP4Y, S6500-48MPP6Y)
MGMT
MST

04 Fampidirana

Omada Campus Stackable L3 Managed Switch

LED

famantarana

Port 1-24 of S6500-24GP4XF/
Port 1-48 of S6500-48GP6XF
(When the SPEED LED is on)

Green On: Mandeha amin'ny 1000 Mbps, fa tsy misy hetsika. Green Flash: mihazakazaka amin'ny 1000 Mbps ary mandefa na mandray angona. Yellow On: Mandeha amin'ny 10Mbps/100 Mbps, fa tsy misy hetsika. Mitselatra mavo: Mihazakazaka amin'ny 10Mbps/100 Mbps ary mandefa na mandray angona. Off: Tsy misy fitaovana mifandray amin'ny seranan-tsambo mifanaraka aminy.

Port 1-24 of S6500-24M4Y & S6500-24MPP4Y/
Port 1-48 of S6500-48M6Y & S6500-48MPP6Y
(When the SPEED LED is on)

Green On: Running at 2.5 Gbps, but no activity. Green Flashing: Running at 2.5 Gbps and transmitting or receiving data. Yellow On: Running at 10 Mbps/100 Mbps/1000 Mbps, but no activity. Yellow Flashing: Running at 10 Mbps/100 Mbps/1000 Mbps and transmitting or receiving data. Off: No device is linked to the corresponding port.

Port 1-24 of S6500-24GP4XF, S6500-24M4Y &
S6500-24MPP4Y/
Port 1-48 of S6500-48GP6XF, S6500-48M6Y &
S6500-48MPP6Y
(Rehefa mandeha ny LED STK)

On: Ny laharan'ny seranan-tsambo dia manondro ny ID unit ao amin'ny topologie stack.

Port 1-24 of S6500-24GP4XF & S6500-24MPP4Y/
Port 1-48 of S6500-48GP6XF & S6500-48MPP6Y
(Rehefa mandeha ny LED PoE)

Green On: The port is supplying power normally. Green Flashing: The supply power exceeds the correponding port’s maximum power. Yellow On: Overload or short circuit is detected. Off: Not providing PoE power on the port

Port 25-28 of S6500-24GP4XF/ Port 49-54 of S6500-48GP6XF ***

Maitso On: Mihazakazaka amin'ny 10 Gbps, fa tsy misy hetsika. Green Flash: mihazakazaka amin'ny 10 Gbps ary mandefa na mandray angona. Mavo Mandeha: Mandeha amin'ny 1 Gbps, fa tsy misy hetsika. Mitselatra mavo: Mihazakazaka amin'ny 1 Gbps ary mandefa na mandray angona. Off: Tsy misy fitaovana mifandray amin'ny seranan-tsambo mifanaraka aminy.

Port 25-28 of S6500-24M4Y & S6500-24MPP4Y/
Port 49-54 of S6500-48M6Y & S6500-48MPP6Y***

Green On: Running at 25 Gbps, but no activity. Green Flashing: Running at 25 Gbps and transmitting or receiving data. Yellow On: Running at 1 Gbps/10 Gbps, but no activity. Yellow Flashing: Running at 1 Gbps/10 Gbps and transmitting or receiving data. Off: No device is linked to the corresponding port.

*By default, S6500-24GP4XF is shipped with a PSM500-AC power supply module, S6500-24M4Y/S650048M6Y is shipped with a PSM550-AC power supply module, and S6500-48GP6XF/S6500-24MPP4Y/ S6500-48MPP6Y is shipped with a PSM900-AC power supply module. One more power supply module needs to be purchased separately.
**By default, both PWR1 and PWR2 will work simultaneously in the load sharing mode. They can also work simultaneously in the redundant power supply mode: for S6500-24GP4XF/S6500-48GP6XF/S650024MPP4Y/S6500-48MPP6Y, you can specify the primary power supply and the backup power supply according to your needs; for S6500-24M4Y/S6500-48M6Y, you can only set PWR1 as the primary power supply and PWR2 as the backup power supply. Generally, the primary power supply takes priority over the backup power supply.
***All 10 Gbps SFP+ slots and 25 Gbps SFP28 slots can be used as uplink ports or stacking ports. When used as stacking ports, the slots need to run at the highest speed.

Fampidirana 05

Omada Campus Stackable L3 Managed Switch The front panel of S7500-26XF6Y is shown as the following figure.
Seranan-tsambo fitantanana

LED

Console Port USB3.0 Port

(RJ45/Type-C)

Fomba Selection

bokotra

10G SFP+ Slot (Port 1-26)

The front panel of S7500-48XF4C is shown as the following figure.

LED 25G SFP28 Slot (Port 27-32)

Button Selection Mode
Seranan-tsambo fitantanana
LED Console Port USB3.0 Port (Type-C/RJ45)

10G SFP+ Slot (Port 1-48)

The front panel of S7500-24Y4C is shown as the following figure.

100G QSFP28 Slot LED (Port 49-52)

Seranan-tsambo fitantanana

LED

Seranan-tsambo USB3.0

Port Console

(RJ45/Type-C)

Button Selection Mode

25G SFP28 Slot

LED

( Seranana 1-24)

The front panel of S7500-48Y8C is shown as the following figure.

100G QSFP28 Slot (Port 25-28)

LED Mode Selection Button

25G SFP28 Slot (Port 1-48)

06 Fampidirana

100G QSFP28 Slot (Port 49-56)

Omada Campus Stackable L3 Managed Switch The front panel of S7500-32C is shown as the following figure.

Button Selection Mode
Management Port LED
Seranan-tsambo USB3.0

Console Port (Type-C/RJ45)

100G QSFP28 Slot

LED

Note: S7500-24Y4C and S7500-48Y8C are designed for installation in Network Telecommunications Facilities (NTFs) where ambient temperature and humidity are controlled.

LED Indication LED
PWR1* PWR2
SY FAN
MGMT
MST
Port 1-26 of S7500-26XF6Y/ Port 1-48 of S7500-48XF4C
(Rehefa mandeha ny LED SPD)
Port 1-24 of S7500-24Y4C/ Port 1-48 of S7500-48Y8C
(When the SPD/SPEED LED is on)

famantarana
Green On: The power supply works properly. Green Flashing: The power supply module is not plugged in properly or not compatible with the switch. Yellow On: The power supply works properly but the switch is powered by the other power supply.** Yellow Flashing: The power supply module is plugged in properly but there’s is no AC power input; abnormal power supply. Off: No power supply module is inserted.
Mitselatra: Miasa tsara ny switch. On na Off: Tsy mandeha araka ny tokony ho izy ny switch.
Maitso: miasa araka ny tokony ho izy ny mpankafy rehetra. Mavo: Tsy ny mpankafy rehetra no miasa tsara.
On: A device is linked to the port. Flashing: Transmitting or receiving data. Off: No device is linked to the port.
Fanamarihana:
For S7500-48Y8C, this LED lights green at 1 Gbps and orange at sub-1 Gbps.
On: The device functions as the master switch in the stack topology or it works individually. Off: The device functions as the member switch in the stack topology.
Maitso On: Mihazakazaka amin'ny 10 Gbps, fa tsy misy hetsika. Green Flash: mihazakazaka amin'ny 10 Gbps ary mandefa na mandray angona. Mavo Mandeha: Mandeha amin'ny 1 Gbps, fa tsy misy hetsika. Mitselatra mavo: Mihazakazaka amin'ny 1 Gbps ary mandefa na mandray angona. Off: Tsy misy fitaovana mifandray amin'ny seranan-tsambo mifanaraka aminy.
Green On: Running at 25 Gbps, but no activity. Green Flashing: Running at 25 Gbps and transmitting or receiving data. Yellow On: Running at 1 Gbps/10 Gbps, but no activity. Yellow Flashing: Running at 1 Gbps/10 Gbps and transmitting or receiving data. Off: No device is linked to the corresponding port.

Fampidirana 07

Omada Campus Stackable L3 Managed Switch

LED

famantarana

Port 27-32 of S7500-26XF6Y ***
(Rehefa mandeha ny LED SPD)

Port 49-52 of S7500-48XF4C/
Port 25-28 of S7500-24Y4C/ Port 49-56 of S7500-48Y8C/ Port 1-32 of S7500-32C***
(When the SPD/SPEED LED is on)

Maitso On: Mihazakazaka amin'ny 100 Gbps, fa tsy misy hetsika. Green Flash: mihazakazaka amin'ny 100 Gbps ary mandefa na mandray angona. Mavo Mandeha: Mandeha amin'ny 40 Gbps, fa tsy misy hetsika. Mitselatra mavo: Mihazakazaka amin'ny 40 Gbps ary mandefa na mandray angona. Off: Tsy misy fitaovana mifandray amin'ny seranan-tsambo mifanaraka aminy.
Fanamarihana:
For S7500-48XF4C/S7500-48Y8C/S7500-32C, the indication above applies only when the 100 Gbps QSFP28 slots work with common cables. When the slots work with 1-to-4 breakout cables, a single slot is split into four 25 Gbps interfaces. In such scenario, the LED will light green only when all four interfaces are working at 25 Gbps (maximum speed), otherwise it will light yellow. When no device is connected to any of the four interfaces, the LED will be off. (The 100 Gbps QSFP28 slots will support 1-to-4 breakout cables in a future software release.)

Port 1-32 of S7500-26XF6Y/
Port 1-48 of S7500-48XF4C/ Port 1-28 of S7500-24Y4C/ Port 1-56 of S7500-48Y8C
(Rehefa mandeha ny LED STK)

On: Ny laharan'ny seranan-tsambo dia manondro ny ID unit ao amin'ny topologie stack.

*By default, S7500-26XF6Y/S7500-48XF4C/S7500-24Y4C/S7500-48Y8C/S7500-32C is shipped with a PSM550-AC power supply module installed respectively. One more power supply module needs to be purchased separately. **By default, both PWR1 and PWR2 will work simultaneously in the load sharing mode. They can also work simultaneously in the redundant power supply mode with PWR1 as the primary power supply and PWR2 as the backup power supply. Generally, the primary power supply takes priority over the backup power supply. ***All 25 Gbps SFP28 slots of S7500-26XF6Y and 100 Gbps QSFP28 slots of S7500-48XF4C/S7500-24Y4C/ S7500-48Y8C/S7500-32C can be used as uplink ports or stacking ports. When used as stacking ports, the slots need to run at the highest speed.
Port Introduction (The Management Port, Console Ports, and USB Ports of S7500-48Y8C are located on the rear panel.)
Management Port Designed to connnect the device for management through web, CLI or SNMP. Do not connect this port to any outdoor device, as this may induce surge and lightning damage. Console Port Designed to connect with a computer for monitoring and configuring the switch. When the switch has an RJ45 console port and a Type-C console port, console input is active on only one console port at a time. By default, the Type-C connector takes priority over the RJ45 connector, or you can change the priority through the web. Do not connect this port to any outdoor device, as this may induce surge and lightning damage. USB Port Designed to install the USB flash disk for data storage. 1000M RJ45 Port Designed to connect to the device with a bandwidth of 10Mbps, 100 Mbps or 1000 Mbps. For PoE switches, the port can also provide power for PDs.

08 Fampidirana

Omada Campus Stackable L3 Managed Switch
2.5G RJ45 Port Designed to connect to the device with a bandwidth of 10 Mbps, 100 Mbps, 1000 Mbps or 2.5 Gbps. For PoE switches, the port can also provide power for PDs. 10G SFP+ Slot Designed to install the 10 Gbps/1 Gbps optical module. 25G SFP28 Slot Designed to install the 25 Gbps/10 Gbps/1 Gbps optical module. 100G QSFP28 Slot Designed to install the 100 Gbps/40 Gbps optical module. Port Feature

MODELY

1000M

2.5G 10G SFP+ 25G SFP28 100G QSFP28 Management Console USB

RJ45 Port RJ45 Port Slot

Slot

Port

Port Port

S6500-24G4XF

S6500-48G6XF

Sary S6500-24GP4XF

Sary S6500-48GP6XF

S6500-24M4Y

S6500-24MPP4Y

S6500-48M6Y

S6500-48MPP6Y

S7500-26XF6Y

S7500-48XF4C

S7500-24Y4C

S7500-48Y8C

S7500-32C

Rear Panel (The figure is for demonstration only. It may differ from your actual product. )
The rear panel of S6500-24G4XF/S6500-48G6XF is shown as the following figure. The figure is for demonstration purposes only. Your switch may differ in appearance from the depicted.

Kensington Security Slot Grounding Terminal Power Socket

Locking Strap Slot

Fanamarihana: PWR1 no famatsiana herinaratra voalohany ary laharam-pahamehana noho ny PWR2.

Fampidirana 09

Omada Campus Stackable L3 Managed Switch
The rear panel of S6500-24GP4XF/S6500-48GP6XF/S6500-24MPP4Y/S6500-48MPP6Y is shown as the following figure. The figure is for demonstration purposes only. Your switch may differ in appearance from the depicted.

Kensington Security Slot

LED

Terminal lehibe

Module amin'ny famatsiana herinaratra

LED

Locking Strap Slot

Note: By default, S6500-24GP4XF is shipped with a PSM500-AC power supply module, and S650048GP6XF/S6500-24MPP4Y/S6500-48MPP6Y is shipped with a PSM900-AC power supply module. One more power supply module needs to be purchased separately. Both PWR 1 and PWR2 can work simultaneously, or you can specify the primary power supply and the backup power supply according to your needs. Generally, the primary power supply takes priority over the backup power supply.
The rear panel of S6500-24M4Y/S6500-48M6Y/S7500-26XF6Y/S7500-48XF4C/S7500-24Y4C is shown as the following figure. The figure is for demonstration purposes only. Your switch may differ in appearance from the depicted.

Terminal lehibe

LED

Power Supply Module Locking Strap Slot

LED

Kensington Security Slot

The rear panel of S7500-48Y8C is shown as the following figure. The figure is for demonstration purposes only. Your switch may differ in appearance from the depicted.

Terminal lehibe

LED

Tady manidy

Slot

Module amin'ny famatsiana herinaratra

10 Fampidirana

ManagemeC(nTtoyPnposeor-tCle/RPJoU4rt5S)B3P.o0wPeorrSt upplyLoMcokdiSnulgoletStraLpED

Omada Campus Stackable L3 Managed Switch
Note: By default, the device is shipped with a PSM550-AC power supply module installed. One more power supply module needs to be purchased separately. When the switch has two power supply modules installed, both PWR1 and PWR2 will work simultaneously in the load sharing mode by default. They can also work simultaneously in the redundant power supply mode with PWR1 as the primary power supply and PWR2 as the backup power supply. Generally, the primary power supply takes priority over the backup power supply.
The rear panel of S7500-32C is shown as the following figure. The figure is for demonstration purposes only. Your switch may differ in appearance from the depicted.

LED LED
Locking Strap Slot
Power Supply Module Kensington Security Slot

Terminal lehibe

LED
Locking Strap Slot

Module amin'ny famatsiana herinaratra

Note: By default, the device is shipped with a PSM550-AC power supply module installed. One more power supply module needs to be purchased separately. When the switch has two power supply modules installed, both PWR1 and PWR2 will work simultaneously in the load sharing mode by default. They can also work simultaneously in the redundant power supply mode with PWR1 as the primary power supply and PWR2 as the backup power supply. Generally, the primary power supply takes priority over the backup power supply.
Power Supply Module The pluggable power supply module PSM500-AC/PSM900-AC/PSM550-AC is an AC-input power supply module. It can convert the input voltage to 53.5 V (12 V for PSM550-AC) with the maximum output power of 500 W/900 W/550 W respectively. Kensington Security Slot Secure the lock (not provided) into the security slot to prevent the device from being stolen.
Grounding Terminal The switch already comes with lightning protection mechanism. You can also ground the switch through the PE (Protecting Earth) cable of AC cord or with Ground Cable. For detailed lightning protection measures, refer to the Lightning Protection Guide from: https://support.omadanetworks.com/r/1004/. Locking Strap Slot Remove the instruction label and insert the AC power cable locking strap into the slot to secure the power cable.

Fampidirana 11

Omada Campus Stackable L3 Managed Switch

Toko 2 Fametrahana

2.1 Ny votoatin'ny fonosana

Ataovy azo antoka fa misy ireto entana manaraka ireto ny fonosana. Azafady mba mifandraisa amin'ny mpaninjara anao, raha misy zavatra voatanisa simba na tsy hita. Ny tarehimarika dia natao ho fampisehoana fotsiny. Ny tena entana dia mety tsy mitovy amin'ny endriny sy ny habeny amin'ny sary.

jiro

Tady herinaratra sy Cable Console

Torolàlana fametrahana
Vahaolana Networking Solution
Torolàlana fametrahana
Omada Campus Stackable L3 Managed Switch

Fametrahana brackets, visy ary tongotra fingotra

2.2 Fiarovana fiarovana
Mba hisorohana ny fahasimban'ny fitaovana sy ny ratra amin'ny vatana vokatry ny fampiasana tsy mety, dia tokony hitandrina ireto fitsipika manaraka ireto ianao.
Fiarovana fiarovana Tazony ny herinaratra mandritra ny fametrahana. Manaova fehin-tànana misoroka ESD, ary ataovy azo antoka fa mifandray tsara amin'ny hoditra ny fehin-tanana ary
miorina tsara. Ampiasao ihany ny tariby herinaratra omena miaraka amin'ny switch. Ataovy azo antoka fa ny famatsiana voltage mifanaraka amin'ny fepetra voalaza ao amin'ny tontonana aoriana ny
switch. Ataovy azo antoka fa napetraka ao amin'ny tontolo misy rivotra tsara ny switch ary tsy misy ny lavaka fanamoriana azy
voasakana. Aza sokafy na esorina ny fonon'ny switch. Alohan'ny hanadiovana ny fitaovana, tapaho ny famatsiana herinaratra. Aza manadio azy amin'ny lamba misy rano, ary na oviana na oviana
use any other liquid cleaning method. Place the device with its bottom surface facing downwards. Only instructed person or skilled person can be allowed to install, replace, or service this device.
Fepetra takiana amin'ny tranokala
Temperature/Hamandoana

12 Fametrahana

Omada Campus Stackable L3 Managed Switch Keep the equipment room at an appropriate level of temperature and humidity. Too much or too little humidity may lead to bad insulation, leakage of electricity, mechanical property changes, and corrosion. High temperatures may accelerate aging of the insulation materials, significantly shortening the service life of the device. To find out the best temperature and humidity conditions for the device, check the Appendix B Specifications. Clearness
Ny vovoka miangona eo amin'ny switch dia azo alaina amin'ny herinaratra static ary miteraka fifandraisana ratsy amin'ny teboka metaly. Nisy ny fepetra noraisina ho an'ilay fitaovana mba hisorohana ny herinaratra static, fa ny herinaratra static mahery loatra dia mety hiteraka fahasimbana mahafaty amin'ireo singa elektronika ao amin'ny board circuit anatiny. Mba hialana amin'ny fiantraikan'ny herin'aratra static eo amin'ny fampandehanan'ny switch, dia asio zava-dehibe ireto zavatra manaraka ireto: Atsipazo tsy tapaka ny fitaovana, ary ataovy madio ny rivotra ao an-trano. Tazony tsara amin'ny tany ny fitaovana ary ataovy izay hahazoana antoka fa nafindra ny herinaratra static. Fikorontanana elektromagnetika
Ny singa elektronika ao anatin'izany ny capacitance sy ny inductance amin'ny fitaovana dia mety hisy fiantraikany amin'ny fanelingelenana ivelany, toy ny famoahana ny capacitance coupling, ny inductance coupling, ary ny impedance coupling. Mba hampihenana ny fanelingelenana, ataovy azo antoka fa handray ireto fepetra manaraka ireto: Ampiasao ny famatsiana herinaratra izay afaka manivana tsara ny fanelingelenana avy amin'ny tambazotran-jiro. Arovy amin'ny fitaovana mandeha matetika sy mahery toy ny fampitana radio ny fitaovana
fiantsonana. Ampiasao ny fiarovan-tena elektromagnetika raha ilaina. Fiarovana ny tselatra
Fametrahana 13

Omada Campus Stackable L3 Managed Switch
avo indrindra voltagNy tondra-drano dia azo avoaka eo no ho eo rehefa misy tselatra ary ny rivotra ao amin'ny lalan'ny famotsorana herinaratra dia mety ho mafana avy hatrany hatramin'ny 20,000 °C. Satria mahery vaika hanimba ny fitaovana elektronika io riandrano eo noho eo io, dia tokony hisy fepetra fiarovana mahomby kokoa amin'ny tselatra. Ataovy azo antoka fa voapetaka tsara ny rack sy ny fitaovana. Ataovy azo antoka fa mifandray tsara amin'ny tany ny socket. Tazony ny rafitra fametahana tariby mitombina ary ialao ny tselatra. Ampiasao ny famantarana SPD (Surge Protective Device) rehefa manao tariby any ivelany.
Fanamarihana: Raha mila fepetra fiarovana amin'ny tselatra amin'ny antsipiriany, jereo ny Torolàlana momba ny fiarovana ny tselatra avy amin'ny: https://support.omadanetworks.com/r/1004/. Site fametrahana
When installing the device on a rack or a flat workbench, attach much importance to the following items: Install the device with its bottom surface facing down only. This equipment is not suitable for use in locations where children are likely to be present. The rack or workbench is flat, stable, and sturdy enough to support the weight of 9.5 kg at least. The rack or workbench has a good ventilation system. The equipment room is well ventilated. The rack is well grounded. Keep the device less than 1.5 meters away from the power socket.
2.3 Fitaovana fametrahana
Phillips screwdriver ESD-mahazaka tariby miaro amin'ny tanana
Fanamarihana: Ireo fitaovana ireo dia tsy tafiditra amin'ny vokatray. Raha ilaina dia afaka mividy azy misaraka ianao.
2.4 Fametrahana vokatra
Ny switch dia natao miaraka amin'ny endri-pamokarana hafanana eo anoloana mankany aoriana. Rehefa miasa izy dia mivezivezy ny rivotra araka ny aseho etsy ambany. Mba hahazoana hafanana tsara kokoa, apetraho ao amin'ny tontolo misy rivotra tsara ilay fitaovana ary avelao ny elanelana 5 ka hatramin'ny 10 sm manodidina ilay fitaovana.
14 Fametrahana

Sary 2-1

Fidiran'ny rivotra

Omada Campus Stackable L3 Managed Switch

Fametrahana Desktop

Raha hametraka ilay fitaovana eo amin'ny desktop, araho ireto dingana ireto:
1. Apetraho amin'ny faritra fisaka ilay fitaovana izay matanjaka ampy hanohanana ny lanjan'ilay fitaovana amin'ny fittings rehetra.

2. Esory ny taratasy fametahana adhesive amin'ny tongony vita amin'ny fingotra.

3. Apetaho eo amin'ny faran'ny fitaovana ny tongotra fingotra mba hisorohana azy tsy ho solafaka rehefa apetraka eo amin'ny birao.

Sary 2-2

Fametrahana Desktop

Feet ambanin'ny fitaovana notch

Fametrahana Rack

Ny fonosana dia misy 6 tsiroaroa amin'ny brackets isan-karazany, ny sarin'izy ireo dia aseho eto ambany ary mety tsy mitovy amin'ny vokatra tena izy.

Sary 2-3

Fametrahana brackets

Screw Hole Group 2

Bracket D Bracket C Bracket B Bracket A

Screw Hole Group 1
Screw Hole Group 3

Bracket F

Screw Hole Group 4-2 (for device with 420mm depth)

Screw Hole Group 5

Lavaka visy

Vondrona 4-1

Screw Hole Group 4-3

(for device with 380mm depth)

(for device with

460mm depth)

Bracket E

Fametrahana 15

Omada Campus Stackable L3 Managed Switch

Before installing the device in an EIA standard-sized, 19-inch rack, please check the efficiency of the grounding system and the stability of the rack, then wear an ESD-preventive wrist strap, and make sure that it has good skin contact and is well grounded. Bracket B, C & E have two adjustable ears, please measure the distance between the front-post rack and the rear-post rack, and determine a suitable mounting method from below:

FOMBA

fampisehoana

Front: Bracket A Rear: Bracket D (Screw Hole Group 1) + Bracket B (Ear towards back)

Rack Distance
(For device with a depth of 380mm)

Rack Distance
(For device with a depth of 420mm)

Rack Distance
(For device with a depth of 460mm)

498-640mm 538-680mm 578-720mm

Front: Bracket A Rear: Bracket D (Screw Hole Group 1) + Bracket C (Ear towards back)

477-498mm 517-538mm 557-578mm

Front: Bracket A Rear: Bracket D (Screw Hole Group 2) + Bracket C (Ear towards back)

429-477mm 469-517mm 509-557mm

Front: Bracket A Rear: Bracket D (Screw Hole Group 2) + Bracket C (Ear towards front)

410-429mm 450-469mm 490-509mm

Front: Bracket A Rear: Bracket D (Screw Hole Group 3) + Bracket C (Ear towards back)

357-410mm 397-450mm 437-490mm

Front: Bracket A Rear: Bracket D (Screw Hole Group 2) + Bracket B (Ear towards back)

282-410mm 322-450mm 362-490mm

16 Fametrahana

Omada Campus Stackable L3 Managed Switch

Front: Bracket A Rear: Bracket F (Screw Hole Group 4) + Bracket E (Ear towards back)

555-936mm 555-936mm 555-936mm

Front: Bracket A Rear: Bracket F (Screw Hole Group 5) + Bracket E (Ear towards back)

743-1121mm 743-1121mm 743-1121mm

Mba hametrahana ilay fitaovana dia araho ny torolàlana voalaza etsy ambany:

1. Attach the M6 nuts to the racks.

Sary 2-4

Securing M6 Nuts

×8

2. Attach the mounting brackets (B, C or E) to the rear-post racks and secure them with the provided M6 screws, as illustrated in the following figure.

Sary 2-5

Installing Brackets on Racks

3. Attach the brackets A & D/F to the switch with the provided M3 screws.

Fametrahana 17

Omada Campus Stackable L3 Managed Switch

Sary 2-6

Installing Brackets on Switch

4. After the brackets are attached to the device, hold the switch with attached brackets up until it aligns with the brackets on the racks, and gently push the switch backwards until it is in place, then secure the device on the racks with M6 screws and fix brackets B/C or E to brackets D or F with M4 screws on both sides.

Sary 2-7

Installing Switch on Racks

Caution: Leave 5 to 10 cm gaps around the devices for air circulation. Avoid placing heavy things on the device. Mount devices in the order demonstrated above and ensure a certain clearance between devices for
the purpose of heat dissipation.

18 Fametrahana

Omada Campus Stackable L3 Managed Switch

Fametrahana Module famatsiana herinaratra

S6500-24GP4XF is shipped with a PSM500-AC power supply module installed, S6500-48GP6XF/ S6500-24MPP4Y/S6500-48MPP6Y is shipped with a PSM900-AC power supply module installed, and S6500-24M4Y/S6500-48M6Y/S7500-26XF6Y/S7500-48XF4C/S7500-24Y4C/S7500-48Y8C/S750032C is shipped with a PSM550-AC power supply module installed. It looks like below, and the image may differ from your actual product.

Sary 2-8

Appearance of the Power Supply Module

AC Power Cord Connector
Fan

Retainer Clips

Extraction Handle

LED

Locking Strap Slot Release Handle

Raha mila manampy mody famatsiana herinaratra iray hafa ianao dia araho ireto dingana ireto:

1. Wear an ESD-preventive wrist strap, and make sure that it has good skin contact and is well grounded.

2. Press the extraction handle of the module with one hand, and hold the bottom of the module using your other hand. Gently push the module in along the slot guide rail.

3. Release the extraction handle to fix the power supply module in place.

Sary 2-9

Fametrahana ny Module momba ny famatsiana herinaratra

Release Handle

Caution: Do not plug the power cord until the power supply module installation is completed. When installing a power supply module, make sure it is set correctly in the operation of installation. Do not use too much force in the installation. If resistance is encountered or positions of the power
supply module appear larger during installation, you must first remove the module and then reinstall the module. If the Retainer Clips cannot spring up naturally and the power module is blocked, it may be due to the power supply module is not installed properly. Please check carefully.
The power supply module is designed with a locking strap slot. If you need to secure the power cable with the included locking strap, please follow the steps:
1. Wear an ESD-preventive wrist strap, and make sure that it has good skin contact and is well grounded.
Fametrahana 19

Omada Campus Stackable L3 Managed Switch
2. Remove the instruction label on the AC power cable locking strap slot. 3. Attach the clamp to the AC power cable and insert the locking strap into the slot. 4. Adjust tightness and distance of the locking strap using clips to ensure the cable is securely fastened.
Figure 2-10 Installing the Locking Strap

Raha mila manala ny maody famatsiana herinaratra ianao dia araho ireto dingana ireto:
1. Wear an ESD-preventive wrist strap, and make sure that it has good skin contact and is well grounded.
2. Depress the retainer clip to release the locking strap, and then remove the power cord from the external power supply system and the power module.
3. Press the extraction handle of the module with one hand, and pull the extraction handle using your other hand, until the module completely comes out of the chassis.
Caution: Unplug the power cord first, then remove the power supply module. When removing a power supply module, make sure that the power supply module is set correctly in the
operation of installation. In order to better protect the power supply module during removal, it is recommended that you
package it in an antistatic bag.
Fan Module Installation
S6500-24GP4XF/S6500-48GP6XF/S6500-24M4Y/S6500-24MPP4Y/S6500-48M6Y/S650048MPP6Y/S7500-26XF6Y/S7500-48XF4C/S7500-24Y4C/S7500-48Y8C/S7500-32C is shipped with hot-swappable fan modules installed. They look like below, and the images may differ from your actual product.
Sary 2-11 Ny endriky ny Module Fan
LED

20 Fametrahana

Extraction Handle Retainer Clips Release Handle

Omada Campus Stackable L3 Managed Switch For normal operation of the switch, please ensure that models with 5 fan modules maintain at least 4 operational modules, while models with 4 fan modules maintain at least 3 operational modules. If one fan module is damaged, please replace it as follows: 1. Wear an ESD-preventive wrist strap, and make sure that it has good skin contact and is well
grounded. 2. Press the extraction handle of the module with one hand, and pull the extraction handle until the
module completely comes out of the chassis.
Sary 2-12 Esory ny Module Fan Simba
3. Press the extraction handle of a new fan module with one hand, and hold the bottom of the module using your other hand. Gently push the module in along the slot guide rail.
4. Release the extraction handle to fix the power supply module in place. Caution: S6500-24GP4XF/S6500-48GP6XF/S6500-24M4Y/S6500-24MPP4Y/S6500-48M6Y/S6500-48MPP6Y/ S7500-26XF6Y uses hot-swappable fan modules with a maximum speed of 9,000 RPM. S7500-48XF4C/ S7500-24Y4C/S7500-48Y8C/S7500-32C uses hot-swappable fan modules with a maximum speed of 18,000 RPM. Please do not interchange or mix fan modules between models. Sharp edges on the fan module may cause injury, so please operate with caution. Make sure the damaged fan module is in place before you are going to replace it. DO NOT unplug the damaged fan module until the replacement operation. Do not use too much force in the replacement. If resistance is encountered or positions of the fan module appear larger during installation, you must first remove the module and then reinstall the module. If the Retainer Clips cannot spring up naturally and the power module is blocked, it may be due to the fan module is not installed properly. Please check carefully.
Fametrahana 21

Omada Campus Stackable L3 Managed Switch

Toko 3 Fifandraisana

3.1 seranan-tsambo Ethernet

Mampifandray seranan-tsambo Ethernet an'ny switch amin'ny solosaina amin'ny tariby RJ45 araka ny asehon'ity sary manaraka ity.

Sary 3-1

Mampifandray ny seranan-tsambo RJ45

Seranan-tsambo RJ45

Tariby RJ45

3.2 10G SFP+/25G SFP28/100G QSFP28 Slot

The following figure demonstrates the connection of 10G SFP+/25G SFP28/100G QSFP28 slot to an optical module

Sary 3-2

Inserting the Fiber Module

Slot Fiber Module

3.3 Port Console
CLI (Command Line Interface) enables you to manage the switch, thus you can load the CLI after connecting the PCs or Terminals to the console port on the switch via a cable (an RJ45 console cable is provided, while Type-C cable is not provided)
Ampifandraiso amin'ny tariby fampiononana ny seranan-tsambo RJ45 an'ny fitaovana amin'ny solosainao araka ny asehon'ity sary manaraka ity.

22 Fifandraisana

Sary 3-3

Mampifandray ny seranan-tsambo Console (RJ45).

Omada Campus Stackable L3 Managed Switch

Ampifandraiso amin'ny tariby Type-C (tsy omena) ny seranan-tsambo console Type-C an'ny fitaovana amin'ny solosainao, araka ny asehon'ity sary manaraka ity.

Sary 3-4

Mampifandray ny Port Console (USB).

Note: RJ45 console port and Type-C console port cannot be used concurrently. Type-C Console port takes
priority over the RJ45 console port. The Type-C console port is hot-pluggable while the RJ45 console port is not. Keep the device power
off when plugging the console cable into the RJ45 console port. Do not connect the console port with other ports by RJ45 cable.
3.4 Hamarino ny fametrahana
Rehefa vita ny fametrahana dia hamarino ireto singa manaraka ireto: Tokony ho 5 ka hatramin'ny 10 sm ny elanelana manodidina ny fitaovana ho an'ny rivotra ary ho azo antoka ny fikorianan'ny rivotra.
dia ampy. Ny voltage ny famatsiana herinaratra mahafeno ny fepetra takiana amin'ny fampidirana voltage ny fitaovana. Ny socket, ny fitaovana ary ny rack dia miorina tsara. Ny fitaovana dia mifandray tsara amin'ny fitaovana tambajotra hafa.
Fifandraisana 23

Omada Campus Stackable L3 Managed Switch

3.5 Herinaratra

Ampidiro ao amin'ny faladian'ny fitaovana ny mpampitohy vehivavy an'ilay tadin-jiro nomena ary ampidiro ao amin'ny fivoahan'ny herinaratra ilay mpampitohy tsara araka ny asehon'ity sary manaraka ity. Ataovy azo antoka fa ny voltage ny famatsiana herinaratra mahafeno ny fepetra takiana amin'ny fampidirana voltage (100-240 V~ 50/60 Hz).

Sary 3-5

Mifandray amin'ny famatsiana herinaratra

Note: The figure is to illustrate the application and principle. The provided plug and module in your region
may differ from the figures above. Generally PWR1 takes priority over PWR2.

3.6 Fanombohana
Rehefa avy mandeha ny fitaovana dia manomboka ny fitsapana ny herin'ny tena izy. Andiana fitsapana maromaro mandeha ho azy mba hahazoana antoka fa mandeha tsara ny fitaovana. Mandritra io fotoana io dia hamaly an'ity lamina manaraka ity ireo tondro LED azy:
1. Ny jiro LED PWR dia mandrehitra ny fotoana rehetra. Ny LED SYS sy ny mari-pamantarana LED an'ny seranana rehetra dia mijanona.
2. Rehefa afaka iray minitra eo ho eo, ny SYS LED sy LED famantarana ny seranan-tsambo rehetra dia hiredareda vetivety ary avy eo dia maty.
3. Segondra maromaro taty aoriana, hiseho ny tondro SYS LED, izay maneho ny fanombohana voalohany.
3.7 Topolojia stack
With stackable design, the switches can be stacked into one stack topology for higher reliability, larger bandwidth, and simpler networking. To build the stack topology, you need to prepare 2-12 switches and enough 10G SFP+/25G SFP28/100G QSFP28 modules/cables. For more details, see the table below:

jiro

Modely mifanentana

Hatrany

S6500-24G4XF S6500-24G4XF, S6500-48G6XF, S6500-24GP4XF, S6500-48GP6XF S6500-48G6XF S6500-24G4XF, S6500-48G6XF, S6500-24GP4XF, S6500-48GP6XF S6500-24GP4XF S6500-24G4XF, S6500-48G6XF, S6500-24GP4XF, S6500-48GP6XF S6500-48GP6XF S6500-24G4XF, S6500-48G6XF, S6500-24GP4XF, S6500-48GP6XF S6500-24M4Y S6500-24M4Y, S6500-24MPP4Y, S6500-48M6Y, S6500-48MPP6Y S6500-24MPP4Y S6500-24M4Y, S6500-24MPP4Y, S6500-48M6Y, S6500-48MPP6Y

2-12 (max 12 in standalone mode, max 4 in controller mode) 2-12 (max 12 in standalone mode, max 4 in controller mode) 2-12 (max 12 in standalone mode, max 4 in controller mode) 2-12 (max 12 in standalone mode, max 4 in controller mode) 2-12 (max 12 in standalone mode, max 4 in controller mode) 2-12 (max 12 in standalone mode, max 4 in controller mode)

24 Fifandraisana

Omada Campus Stackable L3 Managed Switch

S6500-48M6Y S6500-24M4Y, S6500-24MPP4Y, S6500-48M6Y, S6500-48MPP6Y

S6500-48MPP6Y S6500-24M4Y, S6500-24MPP4Y, S6500-48M6Y, S6500-48MPP6Y

S7500-26XF6Y S7500-26XF6Y

S7500-48XF4C S7500-48XF4C

S7500-24Y4C S7500-24Y4C

S7500-48Y8C S7500-48Y8C

S7500-32C

Misy rafitra topolojia telo stack ho an'ny toe-javatra samihafa, azafady manangana ny topolojia mety araka izay ilainao:

1. Topology Chain: Tsotra ny topolojia rojo ary tsy mitaky fifandraisana tariby eo amin'ny vondrona voalohany sy farany. Mety amin'ny stacking lavitr'ezaka izy io, saingy ny fahamendrehany dia somary ambany.

Sary 3-6

Chain Topology

Stacking Port Group 2
Stacking Port Group 1

…

2. Topology peratra: Ny topolojia peratra dia manana fahatokisana ambony kokoa raha oharina amin'ny topolojia rojo. Rehefa tapaka ny iray amin'ireo rojo ao amin'ny topologie peratra dia lasa topologie rojo ny topologie peratra, saingy mbola afaka miasa ara-dalàna ny rafitra stack manontolo. Ny topologie peratra dia mila fifandraisana tariby eo amin'ny vondrona voalohany sy farany, noho izany dia tsy mety amin'ny fametrahana lavitr'ezaka.

Sary 3-7

Ring Topology

Stacking Port Group 2

Stacking Port Group 1

…

Fifandraisana 25

Omada Campus Stackable L3 Managed Switch

3. Topology Star: Ny topology kintana dia mampifandray ny switch amin'ny switch lehibe afovoany, noho izany, dia afaka mampitombo be ny tahan'ny fandefasana data eo amin'ny switch mpikambana raha manome fitantanana iraisana.

Sary 3-8

Topology kintana

Stacking Port Group 2

Stacking Port Group 3

Stacking Port Group 1

…

Note: The stacking port is not allowed to connect to non-stacking port, as it may affect the operation of the
device. Stacking ports with the same group ID are not allowed to connect to stacking ports with different
group IDs, neither to different devices. A stacking port group is a logical port dedicated to stacking and needs to be bound to a stacking port.
A stacking port group can be bound to one or more stacking ports to improve bandwidth and reliability.

26 Fifandraisana

Omada Campus Stackable L3 Managed Switch

Toko 4 Fanamboarana

4.1 Famaranana ny Configurationview
Ny switch dia manohana safidy fanahafana roa:
Fomba tokana: Ampifanaraho sy tantano irery ny switch. Fomba fanaraha-maso: Ampifanaraho sy tantano eo afovoany ireo fitaovana tambajotra. Atolotra ao amin'ny
tambajotra lehibe, izay ahitana fitaovana faobe toy ny teboka fidirana, switch ary vavahady.
Fanamarihana: Rehefa novaina avy amin'ny Mode Standalone mankany amin'ny Mode Controller, dia ho very ny fandrindrana ny switch. Raha mila antsipiriany dia jereo ny antontan-taratasy mifandraika amin'ny foibe fampidinana ny ofisialy webtranokala: https://support.omadanetworks.com/product/.

4.2 Fomba tokana

Ao amin'ny Mode Standalone, ampiasao solosaina iray handrindrana sy hitantanana ny switch mampiasa GUI (Graphical User Interface) na CLI (command-line interface).

Sary 4-1

Topologie ho an'ny fomba tokana

jiro

Mampiasa ny GUI
1. Raha te hiditra amin'ny pejy fitantanana ny switch, dia alao antoka fa ao anaty subnet iray ihany ny switch sy ny solosaina. Sokafy ny mpizaha ary soraty ny adiresy IP an'ny switch ao amin'ny saha adiresy, avy eo tsindrio ny bokotra Enter.
Raha mahazo adiresy IP avy amin'ny mpizara DHCP ny switch (matetika vavahady), tadiavo ny adiresy IP an'ny switch amin'ny mpizara DHCP.
Raha tsy izany dia ampiasao ny adiresy IP default 192.168.0.1 handefasana ny pejy fitantanana ny switch.

2. Raha vao miditra ianao dia apetraho ny solon'anarana sy ny tenimiafina mba hiarovana tsara kokoa ny tambajotranao sy ny fitaovanao. Aorian'izay, ny rafitra dia hamindra anao ho azy hiverina amin'ny fidirana fidirana mba hanamarina miaraka amin'ireo fahazoan-dàlana vao noforonina.

3. Aorian'ny fidirana an-tserasera mahomby dia hiseho ny pejy lehibe. Azonao atao ny manindry ny menus eo amin'ny sisiny ambony sy ankavia hanamboarana ireo fiasa mifanaraka amin'izany.
Raha mila fanazavana fanampiny dia jereo ny Torolàlana ho an'ny mpampiasa sy ny Torolàlana CLI. Ireo torolàlana dia azo jerena ao amin'ny ivon'ny fampidinana ofisialinay webtranokala: https://support.omadanetworks.com/product/.
Mampiasa ny CLI Manangana fifandraisana Telnet na SSH hidirana amin'ny switch amin'ny CLI.

Configuration 27

Omada Campus Stackable L3 Managed Switch

Ampiasao ny seranan-tsambo console hidirana amin'ny switch. Rehefa mampiasa ny seranan-tsambo console dia atombohy ny programa emulation terminal (toy ny Hyper Terminal) amin'ny PC ary amboary ny programa emulation terminal toy izao manaraka izao:

Baud tahan'ny 38400 bps

Takelaka data 8

Parity Tsy misy

Stop Bits 1

Tsy misy fanaraha-maso ny fikorianan'ny rano

Raha mila fanazavana fanampiny dia jereo ny Torolàlana ho an'ny mpampiasa sy ny Torolàlana CLI. Ireo torolàlana dia azo jerena ao amin'ny ivon'ny fampidinana ofisialinay webtranokala: https://support.omadanetworks.com/product/.
Note: You may need to change the password the first time you log in, which will better protect your network and devices.

4.3 Fomba fanaraha-maso
Controller Mode applies to the large scale network with mass devices. All devices can be centrally configured and monitored via Omada Pro Hardware Controller (C5300), Omada Pro Software Controller, or Omada Pro Cloud-Based Controller.
Note: Before the following configurations, make sure the switch can access the internet. When using Omada Pro Hardware/Software/Cloud-based Controller, make sure the switch and the controller are in the same subnet. Typically, the switch obtains IP address from the DHCP server. You can check the switch’s IP address on the DHCP server.

Via Omada Pro Hardware Controller (C5300)

Omada Pro Hardware Controller (C5300) is a good alternative if you have no spare PC to keep running Omada Pro Software Controller in the network. It needs to be purchased additionally. Follow the steps below to configure the Omada Pro Hardware Controller (C5300).

Sary 4-2

Manage the network via Omada Pro Hardware Controller (C5300)

Gateway Switch

Omada Pro Hardware Controller (C5300) EAP
28 Fanamboarana

EAP

Mpanjifa

Omada Campus Stackable L3 Managed Switch

Note: Before you start, be sure to power up and connect your devices according to the topology figure. A DHCP server (typically a gateway with DHCP function enabled) is required to assign IP addresses to
the EAPs and clients in your local network. Omada Pro Controller must have network access to some Omada campus devices (the gateway,
switch, or APs) in order to find, adopt, and manage them.

1. Tadiavo ny adiresy IP an'ny vavahady. Sokafy ny tsipika baiko amin'ny PC-nao ary midira ipconfig. Ao amin'ny lisitry ny vokatra, tadiavo ny Default Gateway, izay adiresy IP an'ny vavahady ihany koa.
2. Alefaso a web navigateur ary ampidiro ny adiresy IP an'ny vavahady. Midira ao amin'ny vavahady web pejy. Avy eo, mandehana any amin'ny Network> LAN> Lisitry ny mpanjifa DHCP hahitana ny adiresy IP an'ny mpanara-maso anao araka ny adiresy MAC-ny.
3. Ampidiro ao amin'ny bara adiresy ny adiresy IP an'ny mpanara-maso anao mba hanokafana azy web pejy.
4. On the Omada Pro Controller’s web pejy, araho ny mpamosavy hamita ny fanamboarana haingana.
5. Aorian'ny fametrahana haingana dia miseho ny pejy fidirana. Ampidiro ny solon'anarana sy ny tenimiafina noforoninao ary tsindrio Log in. Avy eo dia azonao atao ny manitsy ny mpanara-maso.
6. Raha te hitantana ireo fitaovana reomotely ianao dia araho ireto dingana manaraka ireto:
a. Ataovy azo antoka fa ny Cloud Access dia alefa amin'ny mpanara-maso anao. Amin'ny alàlan'ny default, ny Cloud Access dia alefa. Ataovy azo antoka fa mitselatra moramora ny LED rahona.

b. Alefaso a web navigateur ary midira https://omada.tplinkcloud.com ao amin'ny adiresy bar. Ampidiro ny ID sy ny tenimiafinao TP-Link raha te hidirana. Tsindrio + Add Controller ary safidio ny Hardware Controller raha te hampiditra ny controller anao. Avy eo dia azonao atao ny manitsy ny controller.

For more details, refer to the Installation Guide of C5300.

Via Omada Pro Software Controller

Download the Omada Pro Software Controller on a PC with Windows OS or Linux OS. Then run the file and follow the wizard to install the Omada Pro Software Controller. Follow the steps below to configure the Controller.

Sary 4-3

Mitantana ny tambajotra amin'ny alàlan'ny Omada Pro Software Controller

Gateway

jiro

-maso

Omada Pro Software Controller AP

mandeha amin'ny PC Host

Mpanjifa

Configuration 29

Omada Campus Stackable L3 Managed Switch

1. Launch the Omada Pro Software Controller on your PC. After the initiation process, the controller automatically opens its web pejy. Raha tsy izany, tsindrio Manomboha navigateur hitantana ny tambajotra.
2. On the Omada Pro Controller’s web pejy, araho ny mpamosavy hamita ny fanamboarana haingana.
3. Aorian'ny fametrahana haingana dia miseho ny pejy fidirana. Ampidiro ny solon'anarana sy ny tenimiafina noforoninao ary tsindrio Log in. Avy eo dia azonao atao ny manitsy ny mpanara-maso.
4. Raha te hitantana ireo fitaovana reomotely ianao dia araho ireto dingana manaraka ireto:
a. Make sure that Cloud Access is enabled on your controller and your controller has been bound with your TP-Link ID. On the Omada Pro Controller’s web pejy, mankanesa any amin'ny Settings> Cloud Access mba hahafahan'ny Cloud Access ary mamatotra ny ID TP-Link anao. Raha efa natsanganao tao amin'ny fanamboarana haingana dia tsidiho ity dingana ity.
b. Alefaso a web navigateur ary midira https://omada.tplinkcloud.com ao amin'ny adiresy bar. Ampidiro ny ID TP-Link sy ny tenimiafinao hidirana. Hisy lisitry ny mpanara-maso izay mifamatotra amin'ny ID TP-Link anao. Avy eo dia azonao atao ny manindry ny Launch mba hanitsiana bebe kokoa ny controller.

Note: To manage your devices, Omada Pro Software Controller needs to keep running on your computer.

Amin'ny alàlan'ny Omada Pro Cloud-Based Controller

Omada Pro Cloud-Based Controller dia safidy tsara nefa tsy mila mametraka ny controller software amin'ny PC.

Mila vidiana fanampiny ny fahazoan-dàlana.

Sary 4-4

Tantano ny tambajotra amin'ny alàlan'ny Omada Pro Cloud-Based Controller

Cloud omada

Gateway

jiro

Mpanjifa
1. Contact the sales staff to grant the Omada Pro Cloud-Based Controller permission. 2. Launch a web browser and enter https://omada.tplinkcloud.com in the address bar. Log in with
your TP-Link ID.
30 Fanamboarana

Omada Campus Stackable L3 Managed Switch 3. Click + Add Controller and choose Cloud-Based Controller to add an Omada Pro Controller. Then
you can launch the controller to adopt and manage devices. * Omada App With the Omada app, you can also manage your controller at a local site or a remote site via your mobile device. For the detailed configurations, refer to the User Guide of the controller. The guide can be found on the download center of our official webtranokala: https://support.omadanetworks.com/product/.
Configuration 31

Omada Campus Stackable L3 Managed Switch
Fanazavana fanampiny Famahana olana
F1. Inona no azoko atao raha adinoko ny solonanarana sy ny teny miafin'ny switch?
1. Ampifandraiso amin'ny seranan-tsambon'ny console ny seranan-tsambon'ny PC ary sokafy ny programa emulation terminal.
2. Vonoy ary avereno indray ny switch. Ataovy ny hetsika asehon'ny programa emulation terminal mba hahatongavana amin'ny menu bootUtil. Ny hetsika dia samy hafa amin'ny vokatra amin'ny vokatra. Ireto ambany ireto ny zavatra azo atao: · Tsindrio izay fanalahidy hampitsaharana ny autoboot. · Tsindrio ny CTRL-B raha te-hiditra amin'ny menio bootUtil.
3. Haseho ny sakafo bootUtil. Ampidiro ny isa 6 mba hisafidianana ny safidy "Famerenana ny tenimiafina" ary midira Y mba hamafa ny mpampiasa sy ny tenimiafina rehetra. Avy eo dia azonao atao ny mamerina ny solon'anarana sy ny tenimiafina.
Q2. Nahoana no miasa tsy ara-dalàna ny LED PWR? Ny LED PWR/Power dia tokony hazava rehefa miasa ara-dalàna ny rafitra herinaratra. Raha miasa tsy ara-dalàna ny LED PWR/Power dia araho ireto dingana manaraka ireto:
1. Ataovy azo antoka fa mifandray tsara ny tariby herinaratra, ary ara-dalàna ny fifandraisana amin'ny herinaratra. 2. Ataovy azo antoka fa ny voltage ny famatsiana herinaratra mahafeno ny fepetra takiana amin'ny fampidirana voltage ny
switch.
Q3. Inona no tokony hataoko raha tsy afaka miditra amin'ny web pejy fitantanana? Andramo ireto:
1. Jereo ny LED port rehetra eo amin'ny switch ary ataovy azo antoka fa mifandray tsara ny tariby Ethernet. 2. Andramo seranan-tsambo hafa amin'ny switch ary ataovy azo antoka fa mety sy miasa ara-dalàna ny tariby Ethernet. 3. Vonoy ny switch ary, rehefa afaka kelikely, dia velomy indray. 4. Ataovy azo antoka fa ny adiresy IP an'ny PC-nao dia napetraka ao anatin'ny subnet amin'ny switch. 5. Raha mbola tsy afaka miditra amin'ny pejin'ny fanefena ianao dia avereno any amin'ny default ny orinasa. dia
ny adiresy IP an'ny PC-nao dia tokony apetraka ho 192.168.0.x ("x" dia isa avy amin'ny 2 ka hatramin'ny 254) ary ny saron-tambajotra ho 255.255.255.0.
Q4. Nahoana no tsy miseho tsara ny fandaharana emulation terminal? Andramo ireto:
1. Ataovy azo antoka fa ara-dalàna ny famatsiana herinaratra ary mifandray tsara ny tariby console. 2. Hamarino raha ny tariby console no karazana mety. 3. Ataovy azo antoka fa marina ny mari-pamantarana amin'ny programa emulation terminal: amboary ny Bits isan-tsegondra
toy ny 38400, Data bits toy ny 8, Parity toy ny tsy misy, Stop bits toy ny 1, ary ny Flow fanaraha-maso ho tsy misy.
32 Tovana A Famahana olana

Omada Campus Stackable L3 Managed Switch

Fanazavana fanampiny B

Specifications for S6500 Series Switches

zavatra

Votoaty

IEEE 802.3, IEEE 802.3i, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3z, IEEE 802.3ae, IEEE 802.3x

Fenitra

IEEE 802.3af/at (For S6500-24GP4XF, S6500-48GP6XF) IEEE 802.3af/at/bt (For S6500-24MPP4Y, S6500-48MPP6Y)

IEEE 802.3bz, IEEE 802.3by, IEEE 802.3cc (For S6500-24M4Y, S6500-24MPP4Y, S6500-48M6Y, S6500-48MPP6Y)

10BASE-T: 2-pair UTP/STP of Cat. 3,4,5 (maximum 100 m) 100BASE-TX: 2-pair UTP/STP of Cat. 5 or above (maximum 100 m) 1000BASE-T: 4-pair UTP/STP of Cat. 5e or above (maximum 100 m) 2.5GBASE-T: 4-pair UTP/STP of Cat. 5e or above (maximum 100 m) Transmission Medium 1000BASE-SX/LX/LX10/BX10: MMF, SMF 10GBASE-SR/LR: MMF, SMF 10G SFP+ Direct Attach Cable (SM5220-1M, SM5220-3M) 25GBASE-SR/LR: MMF, SMF (SM6110-SR, SM6110-LR) 25G SFP28 Direct Attach Cable (SM6220-1M)

S6500-24G4XF/S6500-24M4Y: PWR1, PWR2, SYS, FAN, MGMT, MST, SPEED, STK, Port 1-24, Port 25-28 S6500-24GP4XF/S6500-24MPP4Y: PWR1, PWR2, SYS, FAN, PoE Max, MGMT, MST, SPEED, STK, PoE, Port 1-24, Port 25-28 LED S6500-48G6XF/S6500-48M6Y: PWR1, PWR2, SYS, FAN, MGMT, MST, SPEED, STK, Port 1-48, Port 49-54 S6500-48GP6XF/S6500-48MPP6Y: PWR1, PWR2, SYS, FAN, PoE Max, MGMT, MST, SPEED, STK, PoE, Port 1-48, Port 49-54

Fanazavana fanampiny B 33

Omada Campus Stackable L3 Managed Switch

Tetibola PoE

For S6500-24GP4XF: 402W (with 1*PSM500-AC, by default) 720W (with 1*PSM900-AC) 720W (with 2*PSM500-AC) 720W (with 1*PSM500-AC and 1*PSM900-AC) 720W (with 2*PSM900-AC) For S6500-48GP6XF: 764W (with 1*PSM900-AC, by default) 384W (with 1*PSM500-AC) 812W (with 2*PSM500-AC) 1176W (with 1*PSM500-AC and 1*PSM900-AC) 1440W (with 2*PSM900-AC) For S6500-24MPP4Y: 751W (with 1*PSM900-AC, by default) 378W (with 1*PSM500-AC) 802W (with 2*PSM500-AC) 1168W (with 1*PSM500-AC and 1*PSM900-AC) 1534W (with 2*PSM900-AC) For S6500-48MPP6Y: 701W (with 1*PSM900-AC, by default) 328W (with 1*PSM500-AC) 752W (with 2*PSM500-AC) 1118W (with 1*PSM500-AC and 1*PSM900-AC) 1484W (with 2*PSM900-AC)

Operating Temperature & Altitude

For S6500-24G4XF/S6500-48G6XF/S6500-24M4Y/S6500-48M6Y: -5 °C to 50 °C (23 °F to 122 °F) @ 300 meters -5 °C to 45 °C (23 °F to 113 °F) @ 2,000 meters -5 °C to 40 °C (23 °F to 104 °F) @ 3,000 meters For S6500-24GP4XF/S6500-48GP6XF/S6500-24MPP4Y/S6500-48MPP6Y: -5 °C to 45 °C (23 °F to 113 °F) @ 2,000 meters -5 °C to 40 °C (23 °F to 104 °F) @ 3,000 meters

Ny mari-pana fitahirizana -40 °C hatramin'ny 70 °C (-40 °F hatramin'ny 158 °F)

Hamandoana miasa 10% ka hatramin'ny 90% RH tsy misy condensing

Hamandoana fitahirizana

5% hatramin'ny 90% RH tsy misy condensing

34 Fanazavana fanampiny B

Omada Campus Stackable L3 Managed Switch

Specifications for S7500 Series Switches

zavatra

Votoaty

Fenitra

IEEE 802.3, IEEE 802.3x IEEE 802.3z, IEEE 802.3ae (For S7500-26XF6Y, S7500-48XF4C, S7500-24Y4C, S7500-48Y8C IEEE 802.3by, IEEE 802.3cc (For S7500-26XF6Y, S7500-24Y4C, S7500-48Y8C) IEEE 802.3 ba, IEEE 802.3bm (For S7500-48XF4C , S7500-24Y4C, S7500-48Y8C, S7500-32C)

1000BASE-SX/LX/LX10/BX10: MMF, SMF 10GBASE-SR/LR: MMF, SMF 10G SFP+ Direct Attach Cable (SM5220-1M, SM5220-3M) 25GBASE-SR/LR: MMF, SMF (SM6110-SR, SM6110-LR) 25G SFP28 Direct Attach Cable (SM6220-1M) 40GBASE-SR4/LR4: MMF, SMF (For S7500-48XF4C, S7500-24Y4C, Transmission Medium S7500-48Y8C, S7500-32C) 40G QSFP+ Direct Attach Cable (For S7500-48XF4C, S7500-24Y4C, S7500-48Y8C, S7500-32C) 100GBASE-SR4/LR4: MMF, SMF (SM9110-SR4 for S7500-48XF4C, S7500-24Y4C, S7500-48Y8C, S7500-32C) 100G QSFP28 Direct Attach Cable (SM9220-1M for S7500-48XF4C, S7500-24Y4C, S7500-48Y8C, S7500-32C)

LED
Operating Temperature & Altitude

S7500-26XF6Y: PWR1, PWR2, SYS, FAN, MGMT, MST, SPD, STK, SFP+, SFP28 S7500-48XF4C: PWR1, PWR2, SYS, FAN, MGMT, MST, SPEED, STK, SFP+, QSFP28 S7500-24Y4C: PWR1, PWR2, SYS, FAN, MGMT, MST, SPD, STK, SFP28, QSFP28 S7500-48Y8C: PWR1, PWR2, SYS, FAN, MGMT, MST, SPEED, STK, SFP28, QSFP28 S7500-32C: PWR1, PWR2, SYS, MGMT, FAN, MST, SPEED, STK, QSFP28 -5 °C to 45 °C (23 °F to 113 °F) @ 300 meters -5 °C to 40 °C (23 °F to 104 °F) @ 2,000 meters -5 °C to 35 °C (23 °F to 95 °F) @ 3,000 meters

Ny mari-pana fitahirizana -40 °C hatramin'ny 70 °C (-40 °F hatramin'ny 158 °F)

Hamandoana miasa 10% ka hatramin'ny 90% RH tsy misy condensing

Hamandoana fitahirizana

5% hatramin'ny 90% RH tsy misy condensing

For S7500-26XF6Y, S7500-48XF4C, and S7500-24Y4C, the maximum operating temperature supported can reach 50 °C (122 °F) @ 300 meters, 45 °C (113 °F) @ 2,000 meters, and 40 °C (104 °F) @ 3,000 meters.
The supported altitude is sea level to 5000 m. It should be noted that when the altitude is above 2000 m, for every 220 meters of altitude increase, the maximum operating temperature will drop by 1°C (1.8°F).

Fanazavana fanampiny B 35

Omada Campus Stackable L3 Managed Switch

Famaritana momba ny Modules famatsiana herinaratra

PSM500-AC
(For S6500-24GP4XF/ S6500-48GP6XF/ S6500-24MPP4Y/ S6500-48MPP6Y)

PSM900-AC
(For S6500-24GP4XF/ S6500-48GP6XF/ S6500-24MPP4Y/ S6500-48MPP6Y)

PSM550-AC
(For S6500-24M4Y/ S6500-48M6Y/ S7500-26XF6Y/ S7500-48XF4C/ S7500-24Y4C/ S7500-48Y8C/ S7500-32C)

Fampidirana herinaratra

100 V240 V~ 50/60 Hz 8A

100-120V (included)~ 50/60Hz 12A (for locations using low voltage, see specifications for specific countries/ regions)
120 (not included)240V~ 50/60Hz 10A (for other locations)

100 V240 V~ 50/60 Hz 7A

Output Voltage

Primary: 53.5 VDC Standby: 12 VDC

Primary: 12 VDC Standby: 12 VDC

Output Current

9.35 A (Max)

16.5 A (Max)

45 A (Max)

Hery mivoaka

500 W (Max)

900 W (Max)

550 W (Max)

Altitude miasa

For PSM500-AC/PSM900-AC: Sea level to 3000 m For PSM550-AC: Sea level to 5000 m

36 Fanazavana fanampiny B

Fampitandremana marika CE
Ity dia vokatra kilasy A. Ao amin'ny tontolo an-trano, ity vokatra ity dia mety hiteraka fitsabahana amin'ny onjam-peo, ka amin'izany dia mety takiana ny mpampiasa handray fepetra sahaza.
Fanambarana momba ny fanarahana ny EU
Ny TP-Link dia manambara fa mifanaraka amin'ny fepetra ilaina sy ny fepetra hafa mifandraika amin'ny torolàlana 2014/30/EU, 2014/35/EU, 2011/65/EU ary (EU)2015/863 ny fifandimbiasana. Ny fanambarana tany am-boalohany momba ny fanarahana ny EU dia azo jerena ao amin'ny https://www.tp-link.com/en/support/ce/
Fanambarana ny fifanarahan'ny UK
Ny TP-Link dia manambara fa ny fifandimbiasana dia mifanaraka amin'ny fepetra ilaina sy ny fepetra hafa mifandraika amin'ny Fitsipika mifanaraka amin'ny Elektromagnetika 2016 sy ny Fitsipika momba ny fitaovana elektrika (fiarovana) 2016.
, .
TANDREMO:
Andry roa, fusing tsy miandany. Tapaho ny mains alohan'ny fanompoana.
Information momba ny fiarovana
· Tehirizo ny fitaovana amin'ny rano, afo, hamandoana na tontolo mafana. · Aza manandrana mamongotra, manamboatra, na manova ny fitaovana. Raha mila serivisy ianao dia mifandraisa aminay. · Apetraho midina midina ilay fitaovana. · Ny plug amin'ny tadin'ny famatsiana herinaratra no ampiasaina ho fitaovana fanalana, ny socket-outlet
mora azo. · Ampifandraiso amin'ny fivoahan'ny rindrina ny vokatra miaraka amin'ny fifandraisana an-tany amin'ny alalan'ny tady famatsiana herinaratra
or plug. · The socket-outlet shall be installed near the equipment and shall be easily accessible. · The PoE ports shall not be used to charge lithium batteries or devices supplied by lithium
bateria.

· Operating temperature: For S6500-24G4XF/S6500-48G6XF/S6500-24M4Y/S6500-48M6Y/S7500-26XF6Y/ S7500-48XF4C/S7500-24Y4C: -5 °C to 50 °C (23 °F to 122 °F) @ 300 meters -5 °C to 45 °C (23 °F to 113 °F) @ 2,000 meters -5 °C to 40 °C (23 °F to 104 °F) @ 3,000 meters For S6500-24GP4XF/S6500-48GP6XF/S6500-24MPP4Y/S6500-48MPP6Y: -5 °C to 45 °C (23 °F to 113 °F) @ 2,000 meters -5 °C to 40 °C (23 °F to 104 °F) @ 3,000 meters S7500-48Y8C/S7500-32C: -5 °C to 45 °C (23 °F to 113 °F) @ 300 meters -5 °C to 40 °C (23 °F to 104 °F) @ 2,000 meters -5 °C to 35 °C (23 °F to 95 °F) @ 3,000 meters
· : S6500-24G4XF/S6500-48G6XF/S6500-24M4Y/S6500-48M6Y/S7500-26XF6Y/S7500-48XF4C/ S7500-24Y4C -5°C 50°C23°F 122°F@ 300 -5°C 45°C23°F 113°F@ 2,000 -5°C 40°C23°F 104°F@ 3,000 S6500-24GP4XF/S6500-48GP6XF/S6500-24MPP4Y/S6500-48MPP6Y -5°C 45°C23°F 113°F@ 2,000 -5°C 40°C23°F 104°F@ 3,000 S7500-48Y8C/S7500-32C -5°C 45°C23°F 113°F@ 300 -5°C 40°C23°F 104°F@ 2,000 -5°C 35°C23°F 95°F@ 3,000
This equipment is not suitable for use in locations
where children are likely to be present.

Azafady vakio ary araho ny fampahalalana momba ny fiarovana etsy ambony rehefa miasa ny fitaovana. Tsy afaka manome antoka izahay fa tsy hisy loza na fahasimbana hitranga noho ny fampiasana tsy ara-dalàna ny fitaovana. Azafady, ampiasao amim-pitandremana ity vokatra ity ary miasa amin'ny risikao manokana.

Raha mila fanohanana ara-teknika, torolalana ho an'ny mpampiasa ary fampahalalana hafa, tsidiho azafady ny https://support.omadanetworks.com/, na jereo fotsiny ny kaody QR.
© 2026 TP-Link 7100002759 REV2.0.1

Documents / Loharano

Omada L3 Campus Stackable Managed Switch [pdf] Boky Torolàlana
L3 Campus Stackable Managed Switch, L3, Campus Stackable Managed Switch, Stackable Managed Switch, Managed Switch, Switch

References

User Manual

L3 Campus Stackable Managed Switch

fepetra arahana

Torolàlana momba ny fampiasana vokatra

Toko 2: Fametrahana

Toko 3: Fifandraisana

Toko 4: Fanamboarana

FAQ

Q: What should I do if the LED indications show an error?

Documents / Loharano

References

Mametraha hevitra

Foana ny valiny