waveshare ESP32-S3 2.8inch Display Development Board User Manual

1. Fampidirana

This manual provides detailed instructions for the waveshare ESP32-S3 2.8inch Display Development Board. This board is a microcontroller development platform featuring a 2.4GHz WiFi and Bluetooth BLE 5 module, integrated Flash and PSRAM, and a 2.8-inch IPS LCD. It is designed for rapid development of Human-Machine Interface (HMI) and other ESP32-S3 applications.

Sary 1: Tapitraview of the ESP32-S3 2.8inch Display Development Board and its core features.

2. Toetran'ny vokatra

• Equipped with high-performance Xtensa 32-bit LX7 dual-core processor, operating up to 240MHz.
• Supports 2.4GHz Wi-Fi (802.11 b/g/n) and Bluetooth 5 (LE) with an onboard antenna.
• SRAM 512KB sy ROM 384KB tafiditra ao anatiny, miaraka amin'ny Flash 16MB sy PSRAM 8MB.
• Features a 2.8-inch IPS LCD display with 240x320 resolution and 262K colors.
• Optional capacitive 5-point touch function controlled via I2C interface, with interrupt support.
• Adapts UART, I2C, and various GPIO interfaces, integrating a full-speed USB port.
• Includes an onboard speaker, QMI8658 6-axis sensor, RTC sensor, TF card slot, and battery recharge management module.
• Supports flexible clock and multiple power modes for low power consumption.

3. Onboard Components

The following diagram and list identify the key components on the ESP32-S3 2.8inch Display Development Board.

Figure 2: Labeled components of the ESP32-S3 2.8inch Display Development Board.

1. ESP32-S3R8
2. Dual-core processor, up to 240MHz operating frequency
3. 16MB Flash
4. QST attitude sensor
5. QMI8658 (6-axis IMU includes a 3-axis gyroscope and a 3-axis accelerometer)
6. Antenna seramika amin'ny onboard
7. 1.5A MP54F-WR
8. GPIO expander chip
9. RTC chip
10. PCF85063 RTC chip
11. MP1603GTF-Z
12. Power module, 2A current (MAX)
13. Battery recharge manager
14. Buzzer
15. TF karatra slot
16. On the back side of the PCB
17. bokotra BOOT
18. bokotra RESET
19. IPEX1 connector (Switching to use external antenna via resoldering the resistor)
20. 2*12PIN 2.54mm pin header
21. RTC battery header (for connecting rechargeable RTC battery)
22. Lohatenin'ny bateria MX1.25
23. MX1.25 2PIN connector, for 3.7V Lithium battery, supports charging and discharging
24. UART header
25. Famantarana ny fiampangana
26. Port USB Type-C
27. Tondro hery
28. I2C header (connecting with internal chip, only supports the I2C peripherals and cannot be mapped to other functions)
29. Battery power supply control button

4. Famaritana ara-teknika

Below are the general and LCD-specific technical specifications for the development board.

Famaritana ankapobeny:

LCD Parameters:

Figure 3: Detailed LCD parameters for the display panel.

Haben'ny drafitra:

Figure 4: Outline dimensions of the development board in millimeters.

5. Torolàlana fananganana

Follow these steps to set up your ESP32-S3 2.8inch Display Development Board:

1. Vahao: Carefully remove the development board and included accessories from the packaging.
2. Fampifandraisana herinaratra: Connect the board to a 5V power source using the USB Type-C port. Alternatively, connect a 3.7V Lithium battery to the MX1.25 2PIN connector for portable operation.
3. Herin'ny voalohany: Observe the power indicator LED to confirm the board is receiving power.
4. Computer Connection (for development): Connect the USB Type-C port to your computer using a compatible USB cable. This will allow for programming and serial communication.
5. Fametrahana mpamily: Ensure necessary USB-to-serial drivers are installed on your computer if the board is not recognized automatically.

6. Torolàlana miasa

The ESP32-S3 board is designed for various applications, from simple embedded systems to complex HMI projects.

Fampandehanana fototra:

• Herim-batana / maty: Use the USB power or battery connection. The board powers on automatically when connected.
• Fifandraisana aseho: If you have the touch version, interact with the display using finger gestures. For non-touch versions, display output is for visual feedback only.
• Fandaharana: Upload firmware to the ESP32-S3 using a compatible IDE (e.g., Arduino IDE, ESP-IDF) via the USB Type-C port.
• bokotra Reset: Press the RESET button to restart the ESP32-S3 microcontroller.
• bokotra BOOT: Hold the BOOT button while pressing and releasing the RESET button to enter bootloader mode for firmware uploading.

Toe-javatra fampiharana:

Figure 5: Potential application scenarios for the development board.

• Human-machine Interface (HMI): Develop interactive user interfaces for various devices, leveraging the display and optional touch functionality.
• LVGL GUI Development: Utilize the LVGL graphics library for creating rich graphical user interfaces with low memory requirements.
• IoT Applications: Integrate with WiFi and Bluetooth for connected devices, data logging, and remote control.
• Sensor Data Visualization: Display data from onboard or external sensors (e.g., QMI8658 6-axis sensor) directly on the LCD.

7. Connectivity and Interfaces

The board offers a variety of interfaces for communication and expansion.

Figure 6: Pinout diagram for various peripheral interfaces.

• USB Type-C: Used for power supply, programming, and serial communication with a host computer.
• Pins GPIO: General Purpose Input/Output pins are available via the 2*12PIN header for connecting external sensors, actuators, and other modules. Refer to the pinout diagram for specific pin assignments.
• UART Header: Dedicated pins for Universal Asynchronous Receiver-Transmitter communication (RXD, TXD).
• I2C Header: Pins for Inter-Integrated Circuit communication (SDA, SCL), primarily for internal chip peripherals.
• WiFi & Bluetooth: Integrated 2.4GHz Wi-Fi and Bluetooth 5 (LE) for wireless connectivity. An onboard ceramic antenna is provided, with an option for an external antenna via the IPEX1 connector (requires resistor resoldering).
• TF Card TF: For external storage, allowing for data logging or storing display assets.

8. tontolo iainana fampandrosoana

The ESP32-S3 board supports popular development environments for ease of programming.

Sary 7: Tohanana tontolo iainana fampandrosoana.

• ESP-IDF: The Espressif IoT Development Framework is the official development framework for ESP32 series chips. It provides a comprehensive SDK and tools, supporting IDEs like Eclipse and VSCode.
• Arduino IDE: A popular open-source electronic prototyping platform that offers a convenient and flexible environment for developing with ESP32 boards.

Refer to the waveshare product wiki or Espressif documentation for detailed guides on setting up these environments and programming the ESP32-S3.

9. Fikojakojana

Proper maintenance ensures the longevity and reliable operation of your development board.

• Fanadiovana: Keep the board clean and free from dust and debris. Use a soft, dry brush or compressed air. Avoid liquid cleaners.
• Fikarakarana: Handle the board by its edges to avoid touching components, especially the display surface. Static electricity can damage electronic components; use anti-static precautions when handling.
• fitahirizana: Store the board in a dry, cool environment, away from direct sunlight and extreme temperatures. Use anti-static bags if storing for extended periods.
• Fitantanana herinaratra: Always disconnect power before making physical changes to the board or connecting/disconnecting peripherals.

10. Famahana olana

If you encounter issues with your ESP32-S3 2.8inch Display Development Board, consider the following:

• Board tsy mandeha:
  • Verify the USB cable is securely connected and functional.
  • Ensure the power source (USB port or battery) is providing adequate power (5V for USB, 3.7V for battery).
  • Check the power indicator LED on the board.
• Fampisehoana tsy mandeha:
  • Confirm the display ribbon cable is properly seated and secured.
  • Ensure your firmware includes the correct display initialization code and drivers.
  • Check for any physical damage to the display or its connector.
• Programming Errors:
  • Verify that the correct board and port are selected in your IDE.
  • Ensure USB-to-serial drivers are correctly installed.
  • Try holding the BOOT button while pressing and releasing RESET to enter bootloader mode before uploading.
  • Check for syntax errors or missing libraries in your code.
• Olana amin'ny fifandraisana Wi-Fi/Bluetooth:
  • Confirm the antenna is properly connected (if using external).
  • Verify Wi-Fi credentials and network availability.
  • Ensure your code correctly initializes and uses the Wi-Fi/Bluetooth modules.

11. Warranty sy fanohanana

For warranty information, technical support, or further assistance, please refer to the official waveshare website or contact their customer service directly. Product documentation, examples, and community forums are often available on the manufacturer's support pages.