AeroCool Blade ATX Semi-Tower PC Case Instruction Manual

1. Fampidirana

The AeroCool Blade is an ATX semi-tower PC case designed for optimal airflow and aesthetic appeal. It features an RGB front panel with preset lighting modes, a full tempered glass side window, and ample space for component installation. This manual provides essential information for the proper setup, operation, and maintenance of your PC case.

Fampahafantarana momba ny fiarovana: Always disconnect power from your system before performing any installation or maintenance. Handle components with care to avoid damage. Refer to individual component manuals for specific installation instructions.

2. Ny votoatin'ny fonosana

• AeroCool Blade ATX Semi-Tower PC Case
• 1 x 120mm RGB Rear Fan (pre-installed)
• 3 x 120mm Front Fans (pre-installed)
• Accessory Kit (screws, standoffs, cable ties)

3. Fametrahana sy fametrahana

3.1 Fanomanana ny Raharaha

Carefully remove the case from its packaging. Place it on a stable, flat surface. Remove the tempered glass side panel by unscrewing the thumb screws at the rear of the case and gently pulling the panel away.

Sary 3.1: anatiny view of the AeroCool Blade PC case, illustrating the layout for component installation.

3.2 Fametrahana Motherboard

1. Install the necessary motherboard standoffs into the motherboard tray according to your motherboard's form factor (ATX, Micro-ATX, Mini-ITX).
2. Apetraho ao amin'ny fisokafana aorian'ny boaty ny ampinga I/O.
3. Apetraho tsara eo amin'ny fitoeran-javatra ny motherboard-nao, ary ampifanaraho amin'ny lavaka eo amin'ny visy.
4. Ampifanaraho amin'ny visy omena ny motherboard.

3.3 Fametrahana Unite famatsiana herinaratra (PSU).

The AeroCool Blade supports bottom-mounted PSUs. Slide your PSU into the dedicated compartment at the bottom rear of the case. Secure it with screws from the rear of the case.

3.4 Fametrahana ny kapila fitahirizana

• Kapila mafy 3.5": Install 3.5" hard drives into the drive cage located beneath the PSU shroud.
• 2.5" SSDs/HDDs: Install 2.5" drives onto the dedicated mounting points on the motherboard tray or behind it.

Figure 3.2: Rear internal view, highlighting cable management routes and 2.5-inch drive mounting locations.

3.5 Expansion Card (GPU) Installation

Remove the necessary expansion slot covers from the rear of the case. Insert your graphics card or other expansion cards into the PCIe slots on your motherboard and secure them with screws.

3.6 Fan and Cooling Installation

The case comes with one 120mm RGB fan pre-installed at the rear and three 120mm fans pre-installed at the front. Ensure all fan cables are connected to appropriate headers on your motherboard or fan controller.

Figure 3.3: A 120mm RGB fan, similar to those pre-installed in the AeroCool Blade case.

3.7 Fifandraisana I/O eo anoloana

Connect the front panel cables (USB 3.0, USB 2.0, HD Audio, Power Switch, Reset Switch, LED Switch, Power LED, HDD LED) to the corresponding headers on your motherboard. Refer to your motherboard manual for exact pin configurations.

4. Torolàlana miasa

4.1 Mamelona

Once all components are installed and connected, replace the side panel. Connect your monitor, keyboard, mouse, and power cable to the PSU. Press the Power button located on the top panel of the case to turn on your system.

Sary 4.1: Eo amin'ny ilany ambony view of the case, indicating the location of the power button and front I/O ports.

4.2 Fanaraha-maso ny Jiro RGB

The AeroCool Blade features an RGB front panel. Use the dedicated LED button on the top panel to cycle through various preset lighting modes and effects. Pressing the button will change the lighting pattern or color.

Sary 4.2: Eo anoloana view of the AeroCool Blade case with its distinctive RGB lighting.

4.3 Front Panel Ports

The top panel provides convenient access to:

• 1 x USB 3.0 seranana
• 2 x USB 2.0 seranana
• HD Audio output
• Fampidirana mikrofona

Connect your USB devices, headphones, and microphone to these ports as needed.

5. Fikojakojana

5.1 Fanadiovana sivana vovoka

Regularly check and clean the dust filters to maintain optimal airflow and prevent dust buildup inside the case. Dust filters are typically located at the top, front, and bottom (under the PSU). Gently remove them and clean with compressed air or rinse with water (ensure they are completely dry before re-installation).

5.2 Fanadiovana ivelany

Fafao amin'ny lamba malefaka ny velaran'ny ivelany amin'ny fonony.amp cloth. Avoid using harsh chemicals or abrasive materials that could damage the finish or tempered glass.

6. Famahana olana

• Tsy mandeha ny rafitra:
  Ensure the PSU is switched on and properly connected to the wall outlet. Verify all power cables from the PSU are correctly connected to the motherboard and components. Check the front panel power switch connection to the motherboard.
• Tsy mandeha ny jiro RGB:
  Ensure the RGB controller (if applicable) and fan RGB cables are securely connected. Press the LED button on the top panel to cycle through modes. If connected to a motherboard header, check motherboard software settings.
• Ireo mpankafy tsy mihodina:
  Verify that all fan power cables are securely connected to the motherboard fan headers or a fan controller. Check BIOS/UEFI settings for fan speed control.
• Tsy mandeha ny USB/Audio eo anoloana:
  Ensure the USB and HD Audio cables from the front panel are correctly connected to the corresponding headers on your motherboard.

7. Famaritana

Figure 7.1: Dimensions of the AeroCool Blade PC Case.

8. Warranty sy fanohanana

Raha mila fanazavana momba ny garantie sy ny fanohanana ara-teknika, jereo azafady ny AeroCool ofisialy. webtoerana na mifandraisa amin'ny mpivarotra eo an-toerana. Tazomy ny porofon'ny fividiananao mba hahazoana antoka.

Antsipiriany ifandraisana: Raha mila fanampiana fanampiny dia tsidiho azafady www.aerocool.io.