GoControl WS15Z5-1 Z-Wave(R) Wall Switch User Manual

Sava lalana

Thank you for choosing the GoControl WS15Z5-1 Z-Wave Wall Switch. This smart switch allows you to control your lighting or other connected loads remotely via a Z-Wave network, as well as manually. It integrates seamlessly into your smart home system, providing convenience and energy efficiency. Please read this manual carefully before installation and operation to ensure proper use and safety.

Information momba ny fiarovana

FAMPITANDREMANA: Risk of Electric Shock. Installation should be performed by a qualified electrician. Disconnect power at the circuit breaker or fuse box before installation or servicing. Use only copper wire for connections. Do not exceed the maximum load ratings.

• Hamarino tsara fa TONGA ny herinaratra eo amin'ny "circuit breaker" alohan'ny hametrahana azy.
• Ity fitaovana ity dia natao hametrahana araka ny National Electric Code sy ny fitsipika eo an-toerana.
• Aza ampiasaina amin'ny toerana lena na izay tratran'ny rano mivantana.
• Ho an'ny fampiasana anatiny ihany.

Fonosana fonosana

• GoControl WS15Z5-1 Z-Wave Wall Switch
• Screws fametrahana
• Wire Nuts (may vary by package)
• User Manual (ity antontan-taratasy ity)

Fametrahana sy fametrahana

Follow these steps carefully to install your GoControl Z-Wave Wall Switch.

1. Wiring the Switch

1. Turn OFF Power: Locate the circuit breaker controlling the switch you are replacing and turn it OFF. Verify power is off by attempting to turn on the light or appliance.
2. Esory ny Switch taloha: Carefully remove the existing wall plate and switch from the wall box. Disconnect the wires from the old switch, noting which wire was connected to which terminal (Line, Load, Neutral, Ground).
3. Fantaro ny tariby:
   • Line (Hot): Usually black, coming from the circuit breaker.
   • entana: Usually black, going to the light fixture or appliance.
   • Tsy miandany: Usually white, often bundled together in the back of the box. (Required for Z-Wave switches).
   • tany: Usually green or bare copper.
4. Ampifandraiso ny Switch vaovao: Connect the wires to the GoControl WS15Z5-1 switch terminals as follows:
   • Connect ny -dalana, wire to the terminal marked "LINE".
   • Connect ny entana wire to the terminal marked "LOAD".
   • Connect ny tsy miandany wire to the terminal marked "NEUTRAL".
   • Connect ny tany wire to the terminal marked "GROUND".

   Ensure all connections are secure. If you are unsure about wiring, consult a qualified electrician.

5. Fametrahana Switch: Carefully push the wired switch into the wall box. Secure it with the provided screws.
6. Mametraka takelaka rindrina: Attach the new or existing wall plate.
7. Ampodio hery: Avereno ON ny herinaratra amin'ny fiatoana.

Sary 1: Eo anoloana view of the GoControl WS15Z5-1 Z-Wave Wall Switch.

2. Fampidirana Z-Wave (Fampiarahana)

To integrate the switch into your Z-Wave network, you need to "include" it with your Z-Wave controller.

1. Put your Z-Wave controller into Inclusion/Pairing mode. (Refer to your Z-Wave controller's manual for specific instructions).
2. On the GoControl WS15Z5-1 switch, quickly press the top or bottom paddle , indray mandeha. The LED indicator on the switch will blink to confirm inclusion mode.
3. The controller will confirm successful inclusion. The switch's LED will stop blinking and remain solid or turn off, depending on its status.
4. If inclusion fails, refer to the Troubleshooting section or try "Exclusion" first.

Figure 2: The Z-Wave logo, indicating compatibility with Z-Wave networks.

Fampandehanana ny Switch

Fanaraha-maso manual

• Tsindrio ny ambony of the paddle to turn the connected load ON.
• Tsindrio ny ambany of the paddle to turn the connected load NIALA.

Z-Wave Control

Once included in your Z-Wave network, you can control the switch remotely using your Z-Wave controller, hub, or compatible smart home application.

• Use your Z-Wave app or controller interface to toggle the switch ON/OFF.
• The switch supports standard Z-Wave commands for basic on/off functionality.

Figure 3: GoControl products integrate with smart home systems for control via smartphones and other devices.

Figure 4: Diagram illustrating GoControl's integration across various smart home categories like Climate, Lighting, Security, Sensors, and Access.

fikarakarana

The GoControl WS15Z5-1 Z-Wave Wall Switch requires minimal maintenance.

• Fanadiovana: Mba hanadiovana ny switch dia fafao amin'ny lamba malefaka.amp lamba. Aza mampiasa mpanadio abrasive na solvents.
• Fanavaozana ny mikirao praogramanao: Check the GoControl website or your Z-Wave controller's documentation for information on potential firmware updates.
• Fikarakarana ankapobeny: Ataovy azo antoka fa tsy tratran'ny hamandoana be loatra na mari-pana tafahoatra ny switch.

Fanamboarana

Z-Wave Exclusion (Removing from Network)

If you need to remove the switch from your Z-Wave network, follow these steps:

1. Put your Z-Wave controller into Exclusion mode. (Refer to your Z-Wave controller's manual for specific instructions).
2. On the GoControl WS15Z5-1 switch, quickly press the top or bottom paddle , indray mandeha. The LED indicator will blink to confirm exclusion mode.
3. The controller will confirm successful exclusion. The switch's LED will stop blinking.

fepetra arahana

Warranty sy fanohanana

GoControl products are designed for reliability and performance. For warranty information, technical support, or further assistance, please visit the official GoControl webtranokala na mifandray amin'ny departemantan'ny serivisy mpanjifany.

Webtranokala: www.gocontrol.com

Mpanamboatra: GOCONTROL