Westek TMDCD60 Hardwire Indoor Countdown 6-Setting Wall Switch Timer User Manual

Sava lalana

The Westek TMDCD60 is a hardwire indoor countdown timer designed to replace a standard wall switch. It provides timed control for lights, fans, heaters, and other devices, automatically turning them off after a selected duration. This manual provides instructions for safe installation, operation, and maintenance of your timer switch.

Information momba ny fiarovana

FAMPITANDREMANA: Atahorana hihozongozona elektrika. Improper installation can lead to serious injury or death. Always turn off power at the circuit breaker or fuse box before beginning installation. Consult a qualified electrician if you are unsure about any part of the installation process.

• Ity fitaovana ity dia natao ho an'ny fampiasana anatiny ihany.
• Hamarino tsara fa voafehy tsara ny fifandraisan'ny tariby rehetra ary mifanaraka amin'ny fehezan-dalàna momba ny herinaratra eo an-toerana.
• Do not exceed the electrical ratings of the device.
• A neutral wire is required for installation. Older homes may not have a neutral wire in the switch box.

Fonosana fonosana

• Westek TMDCD60 Countdown Timer Switch
• Boky torolàlana (torolàlana ity)

Vita ny vokatraview

The Westek TMDCD60 timer switch features a single push-button control and LED indicators for selected time settings. It is designed to fit into a standard wall switch box and can be used with a standard rocker wallplate (not included).

Sary 1: Eo anoloana view of the TMDCD60 timer switch. The face includes a single control button and five LED indicators labeled "10 MIN", "20 MIN", "30 MIN", "60 MIN", and "HOLD".

Fametrahana

1. Vonoy ny hery: Locate the circuit breaker or fuse that controls the switch you are replacing. Turn off the power completely before proceeding. Verify power is off using a voltage tester.
2. Esory ny Switch efa misy: Carefully remove the wallplate and unscrew the existing switch from the wall box. Disconnect the wires from the old switch. Note the connections for reference.
3. Fantaro ny tariby: The Westek TMDCD60 timer requires four wires:
   • tariby mainty (Black Wire): Hot (Line)
   • Tady mena: Load (to the device being controlled)
   • Wire fotsy: tsy miandany
   • Wire maitso: tany

   Ensure your wall box contains a neutral wire. If not, this timer cannot be installed without running a new neutral wire, which should be done by a qualified electrician.

   

   Sary 2: Miverina view of the TMDCD60, illustrating the labeled wires for proper connection.
4. Connect Wires: Using wire nuts (not included), connect the wires from the wall box to the corresponding wires on the TMDCD60 timer switch:
   • Connect ny Mainty wire from the timer to the Hot (Line) wire from the wall box.
   • Connect ny MENA wire from the timer to the entana wire from the wall box (to the light/fan).
   • Connect ny White wire from the timer to the tsy miandany wire from the wall box.
   • Connect ny Maitso wire from the timer to the tany wire from the wall box.
5. Mametraka ny Timer: Carefully fold the wires into the wall box. The timer is deeper than a standard switch, so ensure there is enough space. Secure the timer switch to the wall box using the provided screws.
6. Mametraka Wallplate: Attach a standard rocker wallplate (not included) over the timer switch.
7. Ampodio hery: Avereno indray ny herinaratra eo amin'ny fiatoan'ny faritra na ny boaty fuse.

hetsika

The TMDCD60 timer operates with a single push-button control. Each press cycles through the available countdown settings and the HOLD function.

1. Turning On and Setting Timer: Press the control button once to activate the timer. The timer will cycle through the following settings with each subsequent press:
   • OFF (no LED lit)
   • 10 Minutes (10 MIN LED lights up)
   • 20 Minutes (20 MIN LED lights up)
   • 30 Minutes (30 MIN LED lights up)
   • 60 Minutes (60 MIN LED lights up)
   • HOLD (HOLD LED lights up)

   The connected device will remain on for the selected duration and then automatically turn off. The corresponding LED will indicate the active setting.

2. FANAOVANA HOLD: To keep the connected device on indefinitely, press and hold the control button for approximately one second until the "HOLD" LED illuminates. In HOLD mode, the device will remain on until you press the button again to turn it off or select a countdown setting.
3. Mamono: To turn off the connected device before the countdown finishes or while in HOLD mode, press the control button until no LEDs are lit.

fikarakarana

The Westek TMDCD60 timer switch requires minimal maintenance. To clean the surface, wipe with a soft, damp lamba. Aza mampiasa mpanadio na solvents mikikisana. Ataovy azo antoka fa maty ny herinaratra alohan'ny hanadiovana azy.

Fanamboarana

fepetra arahana

• Modely: TMDCD60
• marika: Westek
• loko: White
• Fampidirana Voltage: 120V AC, 60Hz
• Enta-mavesatra: 15A Resistive, 1000W Tungsten, 500VA Ballast, 1/4 HP Motor
• Fikirana fanovana: 10, 20, 30, 60 minutes, HOLD
• refy: 1"D x 1"W x 1"H (Note: These dimensions typically refer to packaging; the device itself is deeper for in-wall installation.)
• Lanja entana: 4.48 oz
• Karazana fametrahana: Rindrina
• Safidy fomba: Rocker Switch
• Wire tsy miandany: ilaina

Warranty sy fanohanana

This Westek product is covered by a Garantie voafetra 1 taona manomboka amin'ny datin'ny fividianana. Ity fiantohana ity dia manarona ny lesoka amin'ny fitaovana sy ny asa amin'ny fampiasana mahazatra.

For technical support or warranty claims, please contact Westek customer service. You can find more information and contact details on the official Westek webtranokala na amin'ny fitsidihana ny Westek Store on Amazon.